The specific capacity of a 1 meter well is 2 m3 / h/m. What is the urn of the well when it has descended diameter of the well is increased to 2 at must be the safe performance unde ne 15 m descent?

Q: An engineer makes careful measurements with a weir that monitors a rectangular unfinished…

A: (a) The expression for the normal flow rate. Here, Q is the normal flow rate, A is the cross…

Q: Describe about the Well Points as a method of Dewatering Intermediate Depths.

A: The dewatering is defined as “the technique of temporary lowering of the level of ground water”.…

Q: Summarize the energy loss across the jump that you created expressed as a percentage of the upstream…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: Part A Determine the depth y that will produce maximum velocity for the flow. Express your answer in…

A: Hydraulic Characteristic of circular sewer:  As in the figure the sewer shown in figure, is circular…

Q: Q3/Calculate the steady state drawdown at the pumping well which fully penetrates a confined aquifer…

A: Given Discharge 4000 m3/dayTransmissivity 470 m2/dayRadius of influence 100 mDiameter 0.2 mTo find…

Q: 4. For a confined well with 1000gpd withdrawal the draw dawn from several observation well was given…

A: Given data : confined well = 1000gpd Confined well : A well completed in a confined aquifer is…

Q: is composed of coarse sand having a bulk density of 2 g/cm3, K of 0.1 cm/sec, porosity of 0.25 and…

A:

Q: pumping well was drilled penetrating straight into an unconfined aquifer with the thickness of 42…

A:

Q: Situation 5 - A 0.60 m diameter pipeline 30 m long carries 0.4 m^3/s of water.   a. Compute the…

A: given - pipe diameter D = 0.6 m  pipe length L = 30 m  discharge , Q = 0.4 m3/sec

Q: Water is to be pumped out of a deep well under a total head of 95 m. A number of identical pumps of…

A: Data given, Total head H = 95m Design speed N = 1000rpm Sp speed Ns= 900rpm Q = 150 l/s

Q: Compute the borrow-pit volume of the figure below. round answer to nearest whole cubic yard (yd³)…

A:

Q: Could you help me answer the following question? Thank you The local municipality wants to use this…

A: As per the honor code, the first problem is solved.  Given: Pumping rate, q = 2000 gal/min.…

Q: A well is being drilled at a vertical depth per of 10,000 ft while circulating a 9.6-lbm/gal mud at…

A:

Q: A well is completed with 6,000 ft of 2 7/8" tubing. The bottomhole static pressure is 2,000 psi and…

A: process of solving this problem for well flow rate without the specific curves.Here's what we…

Q: A 5.7 m diameter circular concrete culvert has a drainage water flowing at a height of 1.3 m.…

A:

Q: Where suction pumps are used to draw the collected groundwater from the well points, as is common,…

A: Where suction pumps are used to draw the collected groundwater from the well points, as is common,…

Q: 5. A contractor has decided to use a hydraulic backhoe to excavate a 24-inch wide trench for the…

A: Given Data: It is given that Hydraulic backhoe is used to excavate a 24-inch-wide trench for water…

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.