The space between two flat parallel plates is filled with oil. Each side of the plate is 60 cm. The thickness of the oil plate is 12.5 mm. The upper plate which moves at 2.55 m/s requires a force of 98.1 N to maintain the speed. Determine:                 (a) Dynamic viscosity of oil in centi-Poise (b) Kinematic viscosity of oil in Stokes if the specific gravity of the oil is 0.95

Q: In a wide slipper bearing length / the clearance is given by h = hlexp(-x/l), in which hl denotes…

A: given; clearance (h)=h1e-x/lwhere;l=bearing lengthh1=clearance at inlet (at x=0)position of maximum…

Q: The kinematic viscosity of oxygen at 23.5°C and a pressure of 130 kPa (abs) is 0.104 stokes. Using R…

A:

Q: the space between two square flat parallel plates is filled with oil .Each side of the plate is 50…

A:

Q: The space between two square flat parallel plates is filled with oil. Each side of the square plate…

A:

Q: Two stationary plates are separated by oil with a kinematic viscosity value of 7.380 cm2/s and…

A:

Q: Q' is the flow rate per unit width (i.e. has units of m2/s). Express Q' in terms of T When the flow…

A:

Q: Asap

A:

Q: A cylindrical vessel of radius r has in its side wall a hole in which is horizontally joined a…

A:

Q: The viscosity of a fluid is to be measured by a viscometer constructed of two 55-cm-long concentric…

A: The viscosity of a fluid is to be measured by a viscometer constructed of two 55-cm-long concentric…

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 0.9…

A: Given data  side of square plate (a) = 0.9 m  specific weight of oil (γ) = 9780 N/m3 thickness (t) =…

Q: The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade)…

A:

Q: It is desired to determine the surface tension of a particular fluid using a capillary-rise…

A: given; diameter of tube(d)=0.5mm                                     =0.5*10-3mheight of…

Q: Show that the power , necessary to rotate a stirrer (diameter d) with a speed n (s¹) in a fluid of…

A:

Q: Gate AB is subject to fluids on both sides as shown. Determine the following parameters considering…

A: Write the given data. w=1 mb=2 m

Q: A fluid with a velocity of 30 m/s flows past a sphere with a radius of 40 mm. The density and…

A: Given data v=30 m/sR=40 mmρ=1.32 kg/m3 Here, v is the speed, R is the radius and ρ is the density of…

Q: The space between the shaft and sleeve is filled with an oil of viscosity 6.5 stokes and density 900…

A:

Q: Determine the total summation of the y-component surface forces generated by the fluid in unit of…

A: Calculate the velocity of flow at 2.

Q: (i) Discuss about Surface tension with the help of a diagram. (ii) Discuss about the different…

A: Surface tension:-

Q: Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2.…

A: Given Data: Surface tension of glass tube σ=0.072 Nm                      Glass tube inner radius…

Q: The tank in Fig is 120 cm long into the paper. Determinethe horizontal and vertical hydrostatic…

A: Given: The length of the tank, b = 120 cm The temperature of the water, T = 20⁰C

Q: A cylindrical body of 70 mm diameter and 150 mm length falls freely in a 80 mm diameter circular…

A:

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 0.8…

A:

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 83…

A:

Q: A thick 10 kg plate slides down a flat-inclined surface of 20° to the horizontal plane at a terminal…

A:

Q: The space between two flat parallel plates is filled with oil. Each side of the plate is 50 cm. The…

A: We have given The space between two flat parallel plates is filled with oil. Each side of the plate…

Q: By means of a torque T, a disk 1 is rotated with an angular velocity w1. In the gap "between the two…

A: The free-body diagram of the plates is given below,

Q: Two plates each having an area of 5 m^2 are 77 mm apart. The plate on top is fixed while the plate…

A:

Q: Q 14 : Surface tension is ..expressed in N/m. O N/m2. O N2/m. N/m3. O O O

A:

Q: Determine the hydrostatic force and its location by (a)integration method and (b)formula method.

A:

Q: Q: A steel ball of radius (7 cm) is immersedin water and displaced a volume of (0.03 m). The…

A: GIVEN DATA - VOLUME DISPLACED V=0.03m3 WE HAVE TO FIND BUOYANT FORCE

Q: viscosity of water at 70 deg C is 0.00403 poise and its specific gravity is 0.967, determine its…

A:

Q: What is the apparatus used to blow and suction air into and out of the bent glass tubing/rubber…

A: The oldest method used to determine the surface tension is the capillary rise method. The capillary…

Q: A 80 cm tall cylinder is filled with water (ρwater = 1000 kg/m3) and oil (ρoil = 600 kg/m3) and is…

A: To find:  The pressure at the bottom. Given: The height of the cylinder is h=80 cm1 m100 cm=0.8 m.…

Q: What is the minimum surface tension of a fluid that can sustain a gauge pressure of 0.1 kPa in a 0.5…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.