Q' is the flow rate per unit width (i.e. has units of m2/s). Express Q' in terms of TwWhen the flow rate per unit width is Q' = 1.2 x 10-m2/s, the gap between theplates is 5 mm, the device estimates the shear stress at the top wall to be -0.05Pa. Estimate the viscosity of the fluid. As a means of measuring the viscosity, a liquid is forced to flow through two very largeparallel plates by applying a pressure gradient, You can assume that the velocitydpdxbetween the plates is given by1 dpy(h-y)2µ dxu(y)%3D

Answered: Image /qna-images/answer/3d853874-6429-457d-be01-9b21ef4f5521.jpg

Q' is the flow rate per unit width (i.e. has units of m2/s). Express Q' in terms of T When the flow rate per unit width is Q' = 1.2 × 10¬* m²/s, the gap between the plates is 5 mm, the device estimates the shear stress at the top wall to be –0.05 Pa. Estimate the viscosity of the fluid.

Q' is the flow rate per unit width (i.e. has units of m2/s). Express Q' in terms of T When the flow rate per unit width is Q' = 1.2 × 10¬* m²/s, the gap between the plates is 5 mm, the device estimates the shear stress at the top wall to be –0.05 Pa. Estimate the viscosity of the fluid.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

N:A piece of the pipe 300 mm long weighing 13 N and having i.d of olmm is slipped over a vertical shaft 50 mm in diameter and allowed to fall .calculate the approximate velocity attained by the pipe if a film of oil of viscosity 25 pa.s is maintained between pipe and shaft.
Problem 6-1: The Reynolds number is an engineering parameter that relates to the volume flow rate of a fluid 4Q where vis πνd m² through a tube of diameter d as Red the fluid kinematic viscosity. Determine the Reynolds number and its uncertainty by general analysis given d = 50.4 ±0.1 mm, Q = 0.213 +0.005 S v = 0.999 × 10-6 ± 0.005 × 10-6 m². Which variable contributes the most to the overall uncertainty? Assume uncertainties are at 95 % confidence. S
Find the reynolds number if a fluid of viscosity 0.4 Ns/m2 and relative density of 900 Kg/m3 through a 20 mm pipe with a Velocity of 2.5 m/s?
State clearly your assumptions in your solution sheet
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
An inner radius of an artery is 4.00×103 m. Blood flows through the artery at the rate of 1.00 x 10-6 m³ s'. The blood has a dimensional relative viscosity of 5.2 and viscosity of continuous phase with 10.84x103 Pås and a density of 1.06 × 10 kg m³. Compute the kinematic viscosity and åverage blood velocity in the artery.
A gas whose viscosity is 0.98 centipoise flows through a tube 1.0 mm in diameter and 200 mm long. Find the volume in cubic centimetre of the gas which passes through the tube every 10 secs at a pressure of 2 atm.
3) The viscosity of the Newtonian fluid with a density of 650 kg/m³ is determined with a viscometer as shown in the figure below. The required torque (T=F.r) applied to the inner cylinder (r¡ = 4 cm) to rotate with an angular velocity of 6 rad/s is 3x10-7 Nm. If the velocity distribution in the clearance between the cylinders is linear, a) Find the viscosity (µo) of the fluid b) Find the shear stress on the side surfaces in the viscometer if the viscosity varies according to µ= H0 (1-r/r2) where r2 = W=6rad/s 2cm 150mm ri+2 (cm) due to heating during rotation. .fluid
fluid flows with velocity profile of u = 5 y + 1, calculate the shear force due to viscosity if the viscosity of the fluid is 0.2 Pa.s
A 200 mm long pipe slopes down at 1 in 100 and tapers from 0.25m diameter to 0.15 diameter at the lower end. If the pipe carries 100 litres of oil of specific gravity 0.85 find the pressure at the lower end. The upper end gauge reads 50 KPa.