The smallest circle drawn, tangential to the cam profile is called O prime circle O none O pitch cirlce O base circle

Q: is an oval shaped housing in a plate whose thickness is equal to the width of rotor Select one: O a.…

A: The rotor is contained in an oval shaped housing, and performs the common four-stroke cycle of an…

Q: 4. Why do multi-cylinder engines have smaller flywheels than single-cylinder engines? 5. What…

A: singal cylinder engine: A single cylinder engine is a engine with only one cylinder. It consist with…

Q: Explain the type of cam and follower .(power point line)

A:

Q: cam profile based on the displacement diagram below. These are the details for the cam follower set…

A:

Q: Consider a cam follower rising in harmonic motion to a lift of 210 mm as the cam rotates from 160 to…

A: Given   Lift, h = 210 mm  Angle = 190o Find   Displacement, y

Q: Why is it necessary to check a toolpath visually in a CAM system before the system generates the…

A: To Explain : why is it necessary to check a tool path visually in a cam before the system generates…

Q: What are some ways to make sure the proper codes are being posted when using CAM software?

A: Given CAM software To find Verify the actual codes with generated codes

Q: The follower motion is predetermined and will be according to the shape of the cam Select one: True…

A: Cam is the rotating part of the link which is used to convert the rotation to a linear reciprocating…

Q: what is the magnitude of the angular acceleration of the gear, in rad/sec²

A: Given: The velocity of A, v = 1 m/s The acceleration of A, a = 4 m/s2 The length AB, rAB = 500 mm…

Q: Design a plate cam that gives the following motion to a flat-faced follower: Rise 40 mm with…

A: Given For first 120o the rise is 40 mm For 2nd 90o the rise is 30 mm Rest is uniformly deceleration…

Q: possible numbers. Assuming link 2 rotates at a constant rate of 180 rpm CW, determine the velocity…

A:

Q: Hello, please solve this using step by step so i cam unserstand it well. Thank you

A: Given-Information:- N1= 5N2 = 50N3 = 25J1 =3 kg-m2J2 =200 kg-m2J3 = 200 kg-m2k1 =3 N-m/radD2 =1000…

Q: What good does it do to preview a toolpath in a CAM system before the real program code is written?

A: In the realm of computer-aided manufacturing (CAM), the ability to preview a toolpath before…

Q: Construct a single dwell cam with roller follower with the following conditions: 0 degrees to 60…

A: Please find the solution below

Q: 7. What are the rotating wheel positioning parameters? What is the role of each? Why does the rear…

A: Wheel positioning is of the maintenance of automobiles. It is sometimes called breaking or tracking.…

Q: NACA 25012 Chord c = 150 cm 1) What is the CL? 2) What is the position of maximum camber

A:

Q: For a plate cam with translating offset follower with knife-edge similar to the following Figure,…

A:

Q: esign 1 Dwell at zero displacement esign 2 Dwell at zero displacement esign 3 Dwell at zero…

A:

Q: Critically evaluate and justify the different choices of following cam followers with schematic…

A: To evaluate: The different choices of following cam followers

Q: How can different types of cams be classified. Give examples for each type of cam

A: Cam is defined as a mechanical component that is used to drive the other component through a…

Q: Tech a says that the push on the piston top during the power stroke is transferred to the crank…

A: Tech a is correct.

Q: Discuss the main advantages and disadvantages of at least 2 drive systems that can be used to drive…

A: The drive systems that can be used to drive camshaft are chain drive , gear drive and belt drive.

Q: Design a cam in non dimensional form consisting of 5 sections, each having the following…

A:

Q: Design a cam in non-dimensional form that has the following characteristics: In segment 1 from 0 <0…

A:

Q: Design a disk(radial) cam that would satisfy the requirement of the follower. The follower is a…

A:

Q: What's the equivalent mass (meq) of the cam system when it's assumed meq is at point G?

A: Given Figure:

Q: How do you know whether the toolpath is correct before you write the code for it in a CAM system

A: The employment of software and computer-controlled gear to automate a manufacturing process is…

Q: ake a comparative study of 4-stroke SI and CI

A: given: Make a comparative study of 4-stroke SI and CI egines

Q: NACA 24112 Chord c = 150 cm 1) What is the CL? 2) What is the %3D position of maximum camber?

A: Dear student, please find the attached solution.

Q: Please share a pictire or draw this classifications of Cam Disk cam, Plate Cam, or Radial Cam…

A:

Q: gear 6 Slot Cam 6 rod 3 child 5 rod 2 01 Cooontrio 1 Coar 1 Cramo .

A:

Q: Given the following data: Follower type roller follower, off-set to the right by 5mm; lift 30mm;…

A:

Q: For a translating cam-follower system, the pressure angle should: Select one: O a. be 0° O b. be…

A: The cam and follower are a combination of two mechanical components used to utilize the rotational…

Q: ar (normal-tangential) coordinat

A: ωDE = 18 rad/srA = 300 mm =0.3 m rB = 400 mm = 0.4 m rC = 100 mm = 0.1 m To-Determine:- Angular…

Q: (a) Design the profile of a cam (minimum radius of the cam is 1.5 cm) when the knife-edge follower…

A:

Q: Which one of the following statement is CORRECT. The period when the follower is at the top of its…

A: Last statement is correct.

Q: NACA 6412, Chord = 100cm 1) what is the maximum camber? 2) What is the position of maximum camber…

A: Given, Chore length (C) = 100 cm

Q: D3 D4 D1 2400 rpm CW 12" D2 FIGURE 6-41 Speed calculation 7. ©2014 Cengage Learning

A:

Q: QUESTION 5 Consider a cam profile described by (units in cm) r = 7.8581 sin (1.4562 theta) + 14.5307…

A: To find : the base radius of circle in cm  Given :  cam profile described as…

Q: with simple harmonic motion from datum zero to a maximum rise in 100° of cam rotation, dwell for 80°…

A:

Q: Find the correct statement with respect to an offset- follower. a. Motion of follower is along an…

A: To find : Correct statement about offset Follower.  Given statements :  a)  Motion of follower is…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.