The smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of 100mm with 10 active coils. The outer spring is made of 32mm steel spring & has an outside diameter 250mm with 8 active coils. Before the load is applied, the outer spring is 25mm longer than the inner spring. If the load of 90kN is applied to this nest of springs, (a) find the spring rate of each spring; (b) what portion of the total load is carried by each spring? Use G = 80GPa

Q: Problem 8.19 A steel ring shown in Fig. 8.18 is formed in a cir- cular arc subtending an angle of…

A: We know that the steel ring in the illustration is created in a circular arc with a 270o angle at…

Q: Given a spring with 2.032 mm wire diameter, oil tempered, 8 active coils, OD i 8.5 mm. Determine the…

A: To Find : The free lenght Given : The wire diameter is The number of acive coils is The outer…

Q: The drive from a motor to a machine is by means of a crossed flat belt. The shat of the motor and…

A: Given DataNA=1440rpmdA=250mmNB=450rpmx=1.2mSafety Tensile…

Q: Consider four springs with the spring constants: k1 =20 lb/in., k2 = 50 lb/in., k3 = 100 lb/in., k4=…

A: Data given-  K1 = 20 lb /in  K2 = 50 lb /in  K3 = 100 lb/in  K4 = 200 lb/in

Q: If the wire diameter of a compressive helical spring is increased by 2%, the change in spring…

A:

Q: Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each…

A:

Q: the diagram, wrong diagram is wrong. Find the equivalent spr k1= 100 lb/in k2=200 lb/in k3=100 Ib/in…

A:

Q: Inside a helical spring of circular cross-section 20 mm in dimater spring is placed having the same…

A: Spring: It is a mechanical device that carries mechanical energy in it. The energy is stored in it…

Q: 1. A shaft has a diameter of 20 mm, and it is subjected to tensile stress. If the load applied is…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Question 28 Compression coil spring is subjected to load of 500 N is having the mean diameter of 65…

A: For solution refer below images.

Q: spring

A: Lo=120 mmOD=50 mmd=3.4 mm D=OD-d=50-3.4=46.6 mm a) By counting Nt=10.5 turns .Since the ends are…

Q: The external torque on a drill bit varies linearly to a maximum intensity q, in.Ib/in . If the drill…

A:

Q: 4- A helical compression spring is made with oil-tempered wire with wire diameter of 0.2 in, ean…

A: Dear student, in this solution, I have taken some standard values for oil tempered wire from…

Q: A steel helical spring is wound from No. 14 music wire with a mean helix diameter of 0.6 in. The…

A:

Q: A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside…

A: The stress which is induced in a member when the load is applied parallel to the cross section is…

Q: 20k 武 D. EV 5' 30k B. find internal forces in members of thtruss shaun. 4.

A:

Q: The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate…

A: DefinitionS-N Diagram:The S-N diagram can be used to design components that are subject to cycle…

Q: 1. Mean diameter D, inside diameter Din and spring index 2. The expected stress at the operating…

A: We are to determine the dimensions of the spring and the expected stress and deflection of the…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A:

Q: The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15…

A: Given Data The outside diameter of the coil is:D=120 mm The wire diameter is:d=15 mm The number of…

Q: he smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of 00mm…

A:

Q: The rear spring of an automobile has 9 leaves, each with an average thickness of 0 and a width of 2…

A: t=0.242inb=2inL=56intotal weight=1300lb To-Find:- a) Rate of the springb) Maximum stress caused by…

Q: A laminated semi-elliptic leaf spring under a central load of 3000 lb is to have an effective length…

A:

Q: 4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm…

A: Given: Diameter, dw=4 mmouter diameter, OD=32 mmnumber of turns, Nb=3.5design factor, ns=Syσs=1.1

Q: A torsion dynamometer is fitted on a turbine shaft to measure the angle of twist. It is observed…

A: The solution is mentioned in next step

Q: the system is used to lift à mass of A compound lever as shown below. Find the effort 800kg. (10)…

A: As per policy experts are allowed to answer only one question (first one), for the second one please…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.