The slotted arm OA rotates about a horizontal axis through point O. The 0.21-kg slider P moves with negligible friction in the slot and is controlled by the inextensible cable BP. For the instant under consideration, 0 = 32°, @= 0 = 4.5 rad/s, 0 = 0, and r = 0.62 m. Determine the corresponding values of the tension T in cable BP and the force reaction R perpendicular to the slot. The force R is positive if the contact comes from the lower edge of the slot and negative if the contact comes from the top edge. T= r = 0.62 m Answers: R= 16 0.33 m 4.38 i 1.09 B A N Z Z N

The slotted arm OA rotates about a horizontal axis through point O. The 0.21-kg slider P moves with negligible friction in the slot and is controlled by the inextensible cable BP. For the instant under consideration, 0 = 32°, @= 0 = 4.5 rad/s, 0 = 0, and r = 0.62 m. Determine the corresponding values of the tension T in cable BP and the force reaction R perpendicular to the slot. The force R is positive if the contact comes from the lower edge of the slot and negative if the contact comes from the top edge. T= r = 0.62 m Answers: R= 16 0.33 m 4.38 i 1.09 B A N Z Z N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system shown below is released from rest. The static and kinetic coefficients of friction between slider A and the rail are 0.8 and 0.2, respectively. Consider massless-frictionless pulleys and massless cable. Mass of slider B is 15 kg and force P= 25 Newtons is always acting on it. If the acceleration of slider B during the motion is 5 m to the right, determine the tension developed in the cable in Newtons. Consider g =10 m.
The slotted arm OA rotates about a horizontal axis through point O. The 0.18-kg slider P moves with negligible friction in the slot and is controlled by the inextensible cable BP. For the instant under consideration, θ=26∘, ω=θ˙=4.6 rad/s, θ¨=0, and r=0.63 m. Determine the corresponding values of the tension T in cable BP and the force reaction R perpendicular to the slot. The force R is positive if the contact comes from the lower edge of the slot and negative if the contact comes from the top edge. I found R to be equal to 1.05 which is correct, I can't find T.
The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft rotates at a constant angular speed w and the ball travels in a horizontal circle with the strings inclined at a = 30° to the shaft. Given that the tension in string AC is 4 N. Draw a free body diagram of the forces on the ball. Calculate the radial acceleration of the ball. Find the value of the angular speed w. What is the tangential acceleration of the ball? Page 1 of 2 200-g A Fig. 2 /400 mm 400 mm
The body A with a mass of 50 kg is in equilibrium with the help of the pulling force generated in the AB and AC cables in the middle of the inclined plane and the friction force between the curved surface and the object. The friction force is on the line of motion of body A and develops in the opposite direction to the movement in the direction of the arrow shown in the drawing. Since the pulling force in AB and AC cables is 15.1 and 22.1 N, respectively, calculate the balancer friction force acting on the object vectorially? (g = 9.81 m / s'2)
Dynamics
cord 30° P= 34 N Cylinder: r= (25 mm 4 kg m = A uniform cylinder is pasitioned on a 30° slope, and a cord that is wrapped around it leads of in the uphill direction, as shown. A force P (parallel to the slage) is everted on the end of the cord. Assuming that the cylinder tolls without sliding along the slope, find: (a) the acceleration à of the mass center (may and divec) Gatic) (b) the friction force F exerted on the cylinder at the point of contact. A
Q3: The 3-lb collar is released from rest at A and slides freely up the inclined rod, striking the stop at B with a velocity v. The spring of stiffness k = 1.8 lb/ft has an unstretched length of 15 in. Calculate the kinetic energy and v. Note: Use the equation of principle of work and kinetic energy in solution. BAB km 1.60 llyft wwwwwwww 18" 10"
Parvinbhai
3. A 5-kg crate is released from rest at Point A of a 20-kg ramp which is inclined at 40 degrees as shown in the figure below. The lengths of the ramp is 2 m. The interface between the ramp and the ground can be assumed to be frictionless. Use Newton's 2nd Law and the definition of the center of mass to determine the horizontal distance that the ramp has moved when the crate reaches Point B. Neglect the size of the crate. Does your answer depend on the frictional force between the crate and the ramp? e S
The flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity w. Prior to rotation, each of the 0.52-kg sliding blocks has the position x = 28 mm with no force in its attached spring. Each spring has a stiffness of 430 N/m. Determine the value of x for each spring for a steady speed of 279 rev/min. Also calculate the normal force N exerted by the side of the slot on the block. The force N is positive if it pushes from the side labeled A. Neglect any friction between the blocks and the slots, and neglect the mass of the springs. (Hint: Sum forces along and normal to the slot.) Answers: X = wwwwwwww N = i i -74-74- mm mm mm N
The small block B is attached to the vertex A of the right circular cone using a light cord. The cone is rotating at a constant angular velocity about the vertical z-axis such that the block attains a speed of 0.6 m/sec. If the mass of the block is 0.3 kg, determine the tension in the cord by neglecting friction and the size of the block. Present your answer in Newtons using 3 significant figures. 200 mm B 300 mm A 400 mm
The system shown below consists of a uniform disk D that has a mass of mp = 3.0 kg and a radius of r = 0.5 meters. The disk is connected by a massless cable to a block. The system is released from rest and the disk starts rolling without sliding with the angular acceleration of a = 24 rad in the clockwise direction. Determine the tension developed in the cable (in Newtons) at this instant. Consider 0 = 30° and g 10 * mp