The sliding plate viscometer is used to measure fluid viscosity. The top plate (100 mm x 50 mm) is moving to the right with a constant velocity of 22 m/s in response to a force of 1 N. The bottom plate is stationary and separated by a vertical distance of 1 mm from the upper plate. What is the viscosity of the fluid? W F ng L moving plate stationary plate fluid

The sliding plate viscometer is used to measure fluid viscosity. The top plate (100 mm x 50 mm) is moving to the right with a constant velocity of 22 m/s in response to a force of 1 N. The bottom plate is stationary and separated by a vertical distance of 1 mm from the upper plate. What is the viscosity of the fluid? W F ng L moving plate stationary plate fluid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When a fluid is flowing, the velocity gradient is equal to viscosity equal to shear stress o directly proportional to shear stress inversely proportional to shear stress
Problem 3: A honeybee farmer wants to measure the absolute viscosity of his honey. You suggest dropping a 4mm steel ball into a container of honey and measure the time it takes for the ball to pass between two marks as shown. If the time is 13 seconds, what is the honey's viscosity. Assume the density of the honey is 1450 kg/m3 and the density of the steel ball is 7800 kg/m³. Honey 5 cm
۱۵ Q3/ A dash pot is 0.2 m in diameter and 0.25 m long and it slides down in a vertical cylinder of diameter 0.21 m. The lubricating oil filled in the annular space has a viscosity of 0.5 poise and has a linear velocity profile. When the load on the piston is 25 N, find the speed with which the piston slides down. سرعة الله Dash pot Oil Cylinder- 0.2 m 25 N 0.21 m T 0.25 m
Determine the kinematic viscosity (Stokes) of oil having the relative density as 0.91. The shear stress at a point in oil is 1.51 N/m² and the velocity gradient at that point is 0.31 per second. Solution: (i) Viscosity (in Ns/m²) = (ii) Dynamic Viscosity (in poise) = (iii) Mass density of oil (in kg/m³) = iv) Kinematic viscosity (in stokes) =
(Dimensional Analysis) If the velocity V in a fluid flow depends on a dimension 1, the fluid density p, and the viscosity µ, show that this implies that the Reynolds number Vlp/µ is constant.
If the shear rate increases and the viscosity decreases, then how can this fluid be classified?A. Time-independent and thixotropicB. Time-dependent and thixotropicC. Dilatant and thixotropicD. More than one possible answer.
This type of fluid displays a decrease in viscosity as the rate of shear strain is increased. Pseudoplastic Newtonian Bingham plastic Dilatant Thixotropic
The diameter of the sphere is 2 mm. Calculate the value of the Reynolds number for the sphere with 2 mm of diameter when it is moving with a speed of 0.05 m/s. [The value of viscosity is 12 N.s/m² and the value of density is 1300 kg/m']
A device's outer cylinder diameter is 7" and its distance from outer cylinder to the inner cylinder is 0.0356". The said outer cylinder of the device is rotated at 242 rpm and produces a torque of 1.59 lbf-ft. Determine the viscosity of the fluid inside the concentric cylinders of the viscometer it its length is 4'. Express your answer in 7 decimal places and in lbf-s/ft2. (ANSWER MUST BE 7 DECIMALS)
3) The viscosity of the Newtonian fluid with a density of 650 kg/m³ is determined with a viscometer as shown in the figure below. The required torque (T=F.r) applied to the inner cylinder (r¡ = 4 cm) to rotate with an angular velocity of 6 rad/s is 3x10-7 Nm. If the velocity distribution in the clearance between the cylinders is linear, a) Find the viscosity (µo) of the fluid b) Find the shear stress on the side surfaces in the viscometer if the viscosity varies according to µ= H0 (1-r/r2) where r2 = W=6rad/s 2cm 150mm ri+2 (cm) due to heating during rotation. .fluid
A plate separated by 0.1 mm from a fixed plate moves at 0.10 m/s under a force per unit area of 2.0 N/m2. Determine the viscosity of the fluid between the plates. Give your answer in units of mPaos and round to the nearest whole number.
The viscosity of crude oil under conditions of standard temperature and pressure is 7.13(10^-3) N · s/m^2. The viscosity of crude oil in U.S. Customary units (lb · s/ft^2) is?