The sinusoidal voltage v= 200 sin(2m1000 t -60°) is plotted in the figure. Determine the time f 200

Q: Question 5. What is the value of Rin ohms such that the current through the 25 ohm resistance is…

A: Current flowing through the 25ohm is zero when the bridge balancing only then the  The resistance…

Q: ET1 www R1 HIH R2 22 R4 14 R3 ww 23 R1 = 4700 Q R2 = 470 Ω R3 = 1000 Q R4=2200 Q ET = 20 V E across…

A:

Q: Using Nodal analysis, find V1 in Volts if Is = 4.3 A and R = 8.3 Ohms. Give answer in 2 decimal…

A: Given:A network,with To find:The value of V1 using nodal analysis.

Q: 12 13 R1 E2 R3 R2 E1 For the circuit shown above, the emf of the batteries and the resistances are…

A: Node: The meeting point of more than two branches in a circuit is referred as a node. At that node…

Q: Using Nodal analysis, find V1 in Volts if Is = 4.3 A and R = 8.4 Ohms. Give answer in 2 decimal…

A:

Q: -) In the following circuit using Kirchhoff's find: a) The current in each branch of the circuit. b)…

A:

Q: You are handed a black box containing a circuit with two terminals marked a and b. With nothing else…

A: Thevenin voltage is 15 V, the Thevenin resistance is 0.4 ohms, and the resistance of the external…

Q: You are an electrician working in an industrial plant. A circuit contains eight incandescent lamps…

A: Given condition, A circuit contains eight incandescent lamps connected in series across 480 volts.…

Q: Determine Vab in the circuit below

A:

Q: For the circuit shown in Figure 1, determine the equation relating the output voltage to the input…

A: Consider the given circuit,

Q: A small battery-operated flashlight requires a single 1.5-Vbattery. The bulb is barely glowing. But…

A: The terminal voltage is defined as the potential difference across the terminals is called a…

Q: Can a full adder circuit be used as a subtractor? If yes, draw the circuit (please ASAP TIA)

A: A full adder is a circuit that can be used for the summation task and a subtractor is used for the…

Q: After the switch is opened, the equation for the voltage v=A + Be -C volts, where t is in seconds.…

A:

Q: What is the efficiency of a system if the output power is 9 hp and the input voltage is 240 V and…

A:

Q: The figure below shows a battery connected to a circuit. The potential difference across the battery…

A: In this question, we need to determine the current in 12 ohm resistance. We solve this problem using…

Q: Fill in the Blanks Type your answers in all of the blanks and submit A 2 HP motor has an efficiency…

A: In this question we need to find a input power and supply current

Q: Don't use ai to answer I will report your answer Solve it Asap with explanation and calculation

A: Step 1:First we will find current through each resistor :We have been given circuit…

Q: In the circuit in the figure below, determine the following. 200 Ω . 80.0 20.0 40.0 V 70.0 80.0 Ω .…

A:

Q: Find the power supplied or absorbed by the voltage source and current source respectively. Ry RI Is…

A:

Q: V 2 R2 R₁ 0 ww 3 ala Ia Ra 7 6 A B 5 Determine the voltage drop (in volts) from A to B for the…

A: The circuit diagram,

Q: R3 II R2 RI R5

A: Given

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.