The single-phase half wave rectifier has a L=20 mH, R 100 2, andE= 10 V. The input voltage is Vp 120 V ,f 60 Hz, and a=30°. (a)the average output voltage (b) the rms output voltage (c) RF, (d) PFF) TUF.%3D%3D1:2CRVpVs = Vm sin wfVo

Dear student as per our guidelines we are supposed to solve only one question in which it should…

The single-phase half wave rectifier has a L E= 10 V. The input voltage is p 120 V ,f= 60 Hz, and a= 30°. (a) the average output voltage (b) the rms output voltage (c) RF, (d) PF F) TUF. 20 mH, R 100 2, and %3D %3D %3D T1 1:2 'p Vs = Vm sin ot Vo

The single-phase half wave rectifier has a L E= 10 V. The input voltage is p 120 V ,f= 60 Hz, and a= 30°. (a) the average output voltage (b) the rms output voltage (c) RF, (d) PF F) TUF. 20 mH, R 100 2, and %3D %3D %3D T1 1:2 'p Vs = Vm sin ot Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

it's urgent please solve asap
Show the output voltage for the input voltage Vi in the figure by plotting it over a period. (Note: the diode used is a silicon diode and will not be considered ideal.)
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to り:1 L-Dc こ0SA ドL VL-De =20V 220V omsh 0.01 F 0.02 F O 0.0167 F None of the above A Moving to another question will save this response. « F8 F10 %$4 48 & 50 67 7V 8人 99 1O 3. F GJ H. K. Corll %24
A Capacitor filter is used at the output across the load to minimize the ripple factor of the output voltage. If R = 20 02 and the single- phase bridge rectifier is supplied from a 120V - 60 Hz sinusoidal source. Find the capacitor value in millifarads that will maintain the amount of the output ripples to less than 5% 艹 Ce = m₂ 0 mF RL%
For the given circuit below, it operates on a peak-to-peak input voltage of 347.1 V, F = 60 Hz household supply through a step- down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1 D2 AC Input Vsec B (source) D3 D4 Load 24.30 15.96 12.40 O 18.75
Determine the output waveform. Use ideal diode. 15V Vo 7V -15V 37V1 30V 23V 7V -7V -30V A В C D KHH
A 35 V rms sine wave is applied to the input of a certain negative clamper circuit that uses an ideal diode. The dc value of the output is 1- (-35 V) 2- (-60 V) 3- (-40 V) 4- (-50 V) 5- (-70 V) 6- (-80 V)
Based on the simulation results, which diodes turn on during the positive half cycle of the input voltage and during the negative half cycle of the input voltage.
Parallel clipper circuit is given in the figure. Input voltage , Vs= 10 V. Find the voltages obtained on R1, RL and diode. (Note: Take the voltage amplitude as +10, -10V. Take the division value per oscilloscope screen as 5 ms. You can get the function generator frequency value as 50 or 100 Hz.) R-200 20 R |2 2K0 201
Given Vi = 20V peak-to-peak, draw the output waveform for the said clamper circuit below:
choose the correct answer?
A single phase full wave rectifier supplies a 20 Ohm load at an average voltage of 15 V. Determine the source rms voltage. O 23.6 V 16.7 V 9.5 V O 33.3 V