The simply supported steel beam is loaded by the 20 kN - m couple as shown in the figure. Using E = 200 GPa and I = 8x106mm, determine the displacement and slope at the point where the couple is applied. Use Double Integration

Q: Explain the deflection of an RC transfer beam ?

A: Quantifying the deflection of RC beams has been performed traditionally using full-interaction…

Q: 100mm 20mm 200mm 720mm II Locate the centroidal axis and centroidal moment of inertia of the…

A:

Q: Where did 1161 came from at the last part of computation of the deflection at D. Because I put the…

A: Given Data  E = 16500 MPa I = 105 × 106 mm4  Find slope at B and deflection at D using virtual work…

Q: Hello Sir, Good Night I have a question in my homework related structural statics lesson. The…

A: greetings of the day , dear!

Q: onic motion" in industrial engineering (Long Answer and many applications please)

A: Bernoulli’s principle provides a relationship between the pressure of a flowing fluid to its…

Q: The focal length of the object glass of a tacheometer is 320 mm, the distance between the vertical…

A:

Q: As shown in the figure, at point A, the height of the theodolite i=1.400m is measured, and the…

A: Height of the theodolite = 1.400 m The reading of the upper wire = 1.242m The reading of the middle…

Q: Determine static Indetermincay

A: Given data : Number of member (m)=12Number of exertnal support reaction (R)=2+1=3Number of Joint…

Q: Question The focal length of the object glass of a tacheometer is 200 mm, the distance between the…

A: Tacheometer surveying-Middle staff intercepts, s = 2 Spacing, i = 4 mmFocal length, f = 200 mm.The…

Q: How much refraction correction (in m) is required for a distance of 500 m?

A: Given data : Distance (d)=500 m

Q: Compute for the Moment of Inertia about x and y axes.

A: The moment of inertia is the product of the moment and perpendicular distance.  The moment is…

Q: What is Rayleigh waves?

A: A wave is defined as any disturbance propagated in a medium carrying energy from place to place in…

Q: Q-If the spacing between stadia hair and horizontal crosshair in the diaphragm of a tachometer is…

A: Given- Distance between stadia hair and horizontal crosshair d=1.2 mm, focal length f=24 cm,…

Q: Determine the deflection at point C of the beam shown using the Virtual Work Method. (You can verify…

A:

Q: In your own words, Explain What is the difference between Azimuth and Back Azimuth in the military?…

A:

Q: What is known as the change in position of an object? displecment O speed O velocity O none of the…

A:

Q: Micrometer caliper have more accurate measurement than Vernier Caliper?

A: The dimensions measured internally, externally and the depth when measured with help of two set of…

Q: If the thickness of the glass plate of a parallel plate micrometer (in telescope of level…

A:

Q: X 150mm ук k 200 mm 10mm T 75mm Z 95mm 10mm 145mm 10mm Kuwool/ 300mm ↓ Tomm 250mm 10mm T 12 mm ↑ +X

A: First the different areas are marked according to our convenience. Then we find the neutral axis…

Q: 9KN

A:

Q: If the back sight reading at point A is Less than the fore sight reading at point B then * B is…

A:

Q: 5 m 4 m 6 m

A:

Q: A 1 m 10 kN 1 m 5 kN/m 21 2 m B

A:

Q: Why deflection angles are smaller than 180°?

A: Deflection Angle: When a line is deflected from a straight line, the angle made by the deflected…

Q: R AH 8Bject and a plane of reflection are shown on the left below. Select the reflected image from…

A:

Q: The focal length of the object glass of a tacheometer is 200 mm, the distance between the vertic…

A: Given data: Focal length, f = 200 mm. The optical center of the object glass, d = 100 mm. Middle…

Q: The combined correction due to curvature and refraction (in m) for a distance of 1 km on the surface…

A: Given data: Distance, D = 1 m (on the surface of earth).

Q: Why is it important to calculate deflection in beams?

A:

Q: For the section below; i) Determine the position of the center of gravity. ii) Calculate the values…

A:

Q: Question The focal length of the object glass of a tacheometer is 200 mm, the distance between the…

A: Tacheometer surveying-Middle staff intercepts, s = 2 Spacing, i = 4 mmFocal length, f = 200 mm.The…

Q: In your own words, Explain What is the difference between Azimuth and Back Azimuth in the military?…

A: Introduction- Azimuth and back azimuth are the two crucial terms that indicate angles in the…

Q: 1. Locate the centroid of the shaded area figure shown. Yo 1ft 3 ft 2 ft 9 ft 6 ft -Xo

A:

Q: The focal length of the object glass of a tacheometer is 200 mm, the distance between the vertical…

A: Tacheometer surveying- Middle staff intercepts, s = 2  Spacing, i = 4 mm Focal length, f = 200 mm.…

Q: Calculate the horizontal deflection at E. 15kN E = 200GPa 10kN- IAB = 371 x 106 mm4 IBD = 215 x 106…

A: Given,

Q: 50kN 6m X From the picture, analyze: - Internal forces of the truss 6m 6m 40kN * 6m 6m 50kN X 6m 8m

A:

Q: 3 in. in. 2 in. i in. 2 in. i in. Prob. 9-66

A: The location y¯ of the Centroid for a beam having the cross section area is shown. The beam is…

Q: For the simple beam shown, use the virtual work method to find (a) the location and value of the…

A: using Virtual work method##  Calculation of location and value of maxm Rotation and  maxm Deflection…

Q: How the penetrometer operates on the surface?

A: Penetrometer Penetrometer is a device that is used to find the strength of soil or other materials.…

Q: 6KN/m AJ UB Bm 8m

A: We will draw M/EI diagram.

Q: 2. 3. An object and a plane of reflection are shown on the left below. Select the reflected image…

A: In above question , only by visual inspection we can find the answer . In above problem reflected…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.