Under 3 different cell pressures on a water-saturated clay soilsampleTriaxial pressure test with consolidation drainage was performed.Ground tested sample is 38 mm in diameter and 76 mm in height.At the time of collapse in experimentsAccording to the parameters given in the table below;sample12cell pressure200400600(Kpa)Axial load at4808951300the time ofcollapse(kN)Axial length7.228.369.41shortening atthe time ofcollapse(mm)Volume5.257.49.3change at thetime ofcollapse (ml) a) The deviator stress for each test sample and what you will obtainw w m wwhm wfor drained conditionsCalculate the shear strength parameters.b) For experiment no.1, find the effective normal and shear stressesacting on the shear plane.wwwm wwm wcalculate. Determine the angle that the slip plane makes with thehorizontal.wwm ww m w wwww ww mc) In clay soils with the same effective shear strength parametersIf a combined drainless triaxial pressure test has been carried out andthis sample is 240wwwwwww ww vwwww wwwIf KPa had collapsed under cell pressure and 277 kPa deviatoricwwwn bw wwstress,wwwwwWhat will be the pore pressure in the sample at the time of collapse?w mwwm d w b wwwm ww mw mlw

Name: Under 3 different cell pressures on a water-saturated clay soilsample
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Under 3 different cell pressures on a water-saturated clay soilsampleTriaxial pressure test with consolidation drainage was performed.Ground tested sample is 38 mm in diameter and 76 mm in height.At the time of collapse in experimentsAccording to th

To determine: The pore pressure in the sample at the time of collapse

Science

Physics

the shear strength parameters. b) For experiment no.1, find the effective normal and shear stresses wwww www acting on the shear plane. calculate. Determine the angle that the slip plane makes with the horizontal. c) In clay soils with the same effective shear strength parameters If a combined drainless triaxial pressure test has been carried out and this sample is 240 wwm ww If KPa had collapsed under cell pressure and 277 kPa deviatoric stress, www What will be the pore pressure in the sample at the time of collapse? wwwm w

the shear strength parameters. b) For experiment no.1, find the effective normal and shear stresses wwww www acting on the shear plane. calculate. Determine the angle that the slip plane makes with the horizontal. c) In clay soils with the same effective shear strength parameters If a combined drainless triaxial pressure test has been carried out and this sample is 240 wwm ww If KPa had collapsed under cell pressure and 277 kPa deviatoric stress, www What will be the pore pressure in the sample at the time of collapse? wwwm w

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In a fluid, the velocity measured at a distance of 75mm from the boundary is 1.125 m/s. The fluid has an absolute viscosity of 0.048 Pa-s and specific gravity of 0.913. What is the velocity gradient and shear stress at the boundary? Find its kinematic viscosity A 4.9 cu. ft of water is compressed to 5000 psig. What is the volume decrease if the temperature bulk modulus of elasticity of 311.000 psi,
Determine the average normal stress in rod AB and the average normal stress in rod CD
.,..show solutions
Sample of timber with length of 1.1 m. Find the width and thickness (b, d) with logical thickness that give the modulus of rupture =0.75 MPa and failure load (P = 500 N). If you know that load span in flexural is (L= 1 m). - Width of sample? P L/2 Your answer Depth of sample? L/2
Hand written plz The figure on the right shows a slotted ring (radius r. slot width is negligible), which is loaded by two forces of equal magnitude, acting in opposite direction. Determine the stress resultants N, V and M as a function of the angle op.
When water freezes, it expands about 8.65%. What would be the pressure increase inside your automobile engine block if the water in it froze? The bulk modulus of ice is 2.00 x 109 N/m2. Pa Need Help? Read It E Show My Work (Optional) ?
Help me please!
Please answer and solve the question correctly. Thank you!!
Problem 1 ▪5-1. A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1-in.-diameter hole is bored through the shaft? Sketch the shear-stress distribution along a radial line in each case. T
Give me the right solution, Strictly avoid Ai answer.
B. Rolling direction of cold rolled carbon steel has direct effect on tensile, yield strength and the elongation, while the transverse direction have different properties, explain. C. The figure is impact charpy specimen, state the followings;- 1. The tolerances for the following dimensions, V-notch angle, cross section dimensions. 2. State the minimum roughness value (R,) of the charpy specimen. Why? 3. State the name of device that we need to measure the depth of notch and the root dimension. 0.25mm 8mm 10mm (0.394") |(0.315") (0.010") rad. 55mm, (2.165) Momm (0.394") 45
A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 1010 mm, b = 890 mm, c = 1.4 mm, and d = 1.1 mm. R Answer: Shear strain yry prad.