The shaft shown has two pulleys, where pulley C is the input and pulley A is the output. The shaft is supported by frictionless bearings at points O and B. The pulley diameters are dA = 361 mm and dc = 224 mm. The input tensions on pulley C are T3 = 267 N and T4 = 0.10* T3. The shaft diameter, ds = 25 mm. da ХОА ds B dc T3 XAB XBC T₁ • What is the tension T₁ on the output pulley (in N)? Assume the lower tension is 10% of the higher tension.

The shaft shown has two pulleys, where pulley C is the input and pulley A is the output. The shaft is supported by frictionless bearings at points O and B. The pulley diameters are dA = 361 mm and dc = 224 mm. The input tensions on pulley C are T3 = 267 N and T4 = 0.10* T3. The shaft diameter, ds = 25 mm. da ХОА ds B dc T3 XAB XBC T₁ • What is the tension T₁ on the output pulley (in N)? Assume the lower tension is 10% of the higher tension.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A conveyor is used to drive the inertial load of 0.02 kg m² in the required speed range with a brushless DC motor and a gearhead having reduction ratio of 15:1 as shown in the figure below. The belt speed is V=1 m/s and the roller diameter is D=0.1 m. Choose the correct statement. Load Motor Right Angle Gearhead O The moment of inertia of the load referred to the motor shaft is 0.00133 kg m² O The moment of inertia of the load referred to the motor shaft is 0.0133 kg m² O The rotation speed of the motor shaft is 1665 RPM O The rotation speed of the gear shaft is 100 RPM O The rotation speed of the motor shaft is 2865 RPM.
The pinion (gear 2 on shaft a) rotates at 695 rev/min clockwise and transmits 1497 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 3 mm, and gears 4 and 5 have a module of 2 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. Co 18T- 327 X 18T 5 -48T
12 For the mechanism shown in figure, degree of I GV (b) 1 (c) 2 G
3. A flat annular steel flywheel of outer radius 0.5 m and inner radius 0.125 m with p = 7800 kN*s?/m* and v = 0.3 is to be shrunk fit around a solid steel shaft. The shrinking allowance is 0.1 mm. Both materials are the same type of steel with E = 210 GPa. Determine the RPM when the shrink fit loosens as a result of rotation.
The pinion (gear 2 on shaft a) rotates at 635 rev/min clockwise and transmits 1305 W through the idler pair (gears 3 and 4 on shaft b) to the output gear (gear 5 on shaft c). Gears 2 and 3 have a module of 2 mm, and gears 4 and 5 have a module of 3 mm. Pressure angles are all 20 degrees. Solve for the magnitude of the force that shaft b must apply to gears 3 and 4 to maintain static equilibrium in the figure shown here. The figure is not to scale. 187 327 487
solve show all steps and solution
Please read the instructions carefully and do what are asks. Illustrate and show the COMPLETE SOLUTIONS. Consider FN=70, SN=50.
Please I want answer of that question from these choices
need it correctly
What are the maximum, minimum, and average power values for the shaft shown in the figure below if the shaft speed is 50 rpm, l = 14 cm, a = 4 cm, b = 12 cm, P = 750 N, Tmin = -200 N-m, Tmax = 400 N-m.
Example 2 A shaft carries four masses A, B, C and D of magnitude 200 kg, 300 kg, 400 kg and 200 kg respectively and revolving at radii 80 mm, 70 mm, 60 mm and 80 mm in planes measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks measured anticlockwise are A to B 45°, B to C 70° and C to D 120°. The balancing masses are to be placed in planes X and Y. The distance between the planes A and X is 100 mm, between X and Y is 400 mm and between Y and D is 200 mm. If the balancing masses revolve at a radius of 100 mm. Find their magnitudes and angular positions of the balancing mass.
TI=30NM, T2=155NM, T3=85NM and dBC=22mm. 12 010 T3 T2 T1 3-1892615112 D 010 b180106003- 1892615112 \dcp 1826151126 b180106003-18926 dBC B. `dAB b180100003-18926151126 In the figure above, torques TI, T2 and T3 are applied, respectively, to discs A, B and C on the shaft, which is fixed at point D. 3-1892815112s b180106003-18926 The diameters of the shaft segments are indicated in the figure and their values are given below (if they are required). Length of each segment on the shaft has the same value and is equal to L(AB)=L(BC)=L(CD)=400 mm. b180106003- 18926151126 Shear modulus of the material is 80 GPa. o-18926151126 b180108003-18926 Calculate the maximum shear stress g003-18926151126 003-18926 b18 on shaft segment BC. 010600s28151128 B A 46 MPa 60 MPа b180106003- 18926 b180106003- 1892615112 b180106003- 18928151126 38 MPa b180100003-1892615112 57 MPa b180106003- 18926151126 E b180108003-18928 31 MPа b180106003- 18926151126 b180106003- 18926151128 b180106003- 18928151126…