The second order RLC circuit below has a DC source voltage V=220V. L=2mH, C=0.05µF and R=160. Initially, both the capacitor and the inductor are discharged. If the switch is closed at t=0, then the damping factor a and the resonant frequency wo are equal to: 一 W D %3D Select one: O a, 40000, 100000 O b. None of these O c. 4000. 100000 O d. 20000, 50000

The second order RLC circuit below has a DC source voltage V=220V. L=2mH, C=0.05µF and R=160. Initially, both the capacitor and the inductor are discharged. If the switch is closed at t=0, then the damping factor a and the resonant frequency wo are equal to: 一 W D %3D Select one: O a, 40000, 100000 O b. None of these O c. 4000. 100000 O d. 20000, 50000

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. A 20-µF capacitor is conmected in series with a 1.2-mH coil. What is the resonant frequency of this connection? (1. -) 2nVLC
Design an Astable Multivibrator circuit using 555 IC for a frequency of 2KHz.SelectT2 =0.2ms& CapacitanceC1=0.01μF.
14. What is the resonant frequency of a circuit having a resistance of 2 000 ohms, inductance of 0.04mH, and a capacitance of 300 mF?
What is the La place transform of the current across the capacitor if C=0.4F.
Electronic In the circuit in the figure, Rs = 3.8 kΩ, R1 = 82 kΩ, R2 = 22 kΩ, RC = 5.6 kΩ, RE = 1.5 kΩ and RL = 3.3 kΩ and β = 150. Given that the capacitances are C1 = 0.5 μF and C2 = 0.84 μF, what is the low cutoff frequency of the given circuit? NOTE-1: In the middle band frequency, β = 150 will be taken and the frequency dependence of β will not be taken into account. NOTE-2: The output impedance of the transistor r0 will be neglected in the calculations.
For a series RLC circuit, how much inductance (in mH) is needed to resonate at 6.1 kHz with a capacitance of 17.7 nF? (Use 2 decimal places. Unit is not required.)
A 60microfarad capacitor is connected to a 110V 59HZ signal. What is its impedance in Ohms? 45 6 600 O 2.4 O 3.6
What is the value of quality factor of a series RLC circuit having capacitance of 0.01 mF, inductance of 1 mH and resistance of 75 ohms ?
A Reconfigurable RCL Circuit. A series RCL circuit is composed of a resistor (R = 220 0), two identical capacitors (C = 3.70 nF) connected in series, and two identical inductors (L = 5.30 x 10-5 H) connected in series. You and your team need to determine: (a) the resonant frequency of this configuration. (b) What are all of the other possible resonant frequencies that can be attained by reconfiguring the capacitors and inductors (while using all of the components and keeping the proper series RCL order)? (c) If you were to design a circuit using only one of the given inductors and one adjustable capacitor, what would the range of the variable capacitor need to be in order to cover all of the resonant frequencies found in (a) and (b)? (a) Number 359 Units kHz (b) Ceg(parallel) and Leg(series) Number i 359 Units kHz Ceq(series) and Leg(parallel) Number 719 Units kHz Ceq(parallel) and Leg(parallel) Number i Units 180. kHz (c) Maximum capacitance Number i 1.50e-8 Units nF Minimum…
What is the initial voltage for the capacitor? R= 12.5 kQ |İL Us C= 0.8 mF L=2 H Assume vs is given by 1.5 -@ =4 rad/s 1 0.5 ell
SOLVE STEP BY STEP IN DIGITAL FORMAT (a). For the following circuit, graph the output voltage vo(t) when the input voltage is a square waveform like the one shown. Assume that the capacitor, once charged, does not discharge. Vin (t) +10V -15И (Vin) Vin(t) (7) C D =5V + R vo(t)
9. For the circuit shown in figure find (a) The resonant frequency co (b) Zin() Lin ww ΤΩ ele 9 μF 20 mH 0.12