Please answer 3.2 only with reference to 3.1 Question 33.1.The 10 kg disk shown below is pin supported at its center. Determine thenumber of revolutions it must make to attain a speed of 150 rpm starting fromrest. It is acted upon by the constant force F = 10 N, which is applied to thecord wrapped around its periphery, and a constant couple moment T = 5 Nm.Neglect the mass of the cord in the calculations.T= 3 Nm.0.2 mF= 10N3.2.The same disk is suddenly unbalanced and its axis passing through its masscenter G. If it is released from rest, determine the horizontal and verticalcomponents of reaction at the pin O as shown below.1000,10 kg

Answered: Image /qna-images/answer/f5138350-95d2-406b-82fc-33cc4a9b327b.jpg

The same disk is suddenly unbalanced and its axis passing through its mass center G. If it is released from rest, determine the horizontal and vertical components of reaction at the pin O as shown below. 3.2. 100 G 0, 10 kg

The same disk is suddenly unbalanced and its axis passing through its mass center G. If it is released from rest, determine the horizontal and vertical components of reaction at the pin O as shown below. 3.2. 100 G 0, 10 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer all the points, please
45° AZ. 4.4.1 Solve for d1, 02, 03 using the geometric method:
Q2: The crate weighing 996 N is supported by a cable system as shown in figure: 1-The tension in cable AC is: F 24 7 E 4 3 A Crate 416.25 N 397.50 N 603.75 N 622.50 N None of these O O O O O L//////
QI: The three forces shown in Figure are required to cause a 250 N as a resultant acting horizontally through point A, determine the values of P, F and T. F E 1 cm 1 cm A
A 50.0N weight uniform 4 metre long beam is hanging from a cord held out at a 30° angle as shown. And unknown weight not shown in the diagram is also hanging 1 m from the X on the diagram. A) The tension in the cord is measured with a spring balance and found to be 130 N. find the counter clockwise torque from the cord about the X shown in the diagram. B) balance torques to find the torque from the unknown weight that is not shown in the diagram Hint: add the unknown weight to the diagram and do not forget to include the weight of the beam in your calculation
1. For this series of 4 questions, a rider rides in a car that is connected to a 4-m rod, and rotates about the z axis. The rod of negligible mass is subjected to a constant couple moment of M, and the engine of the car supplies a traction force of F. Neglect the size of the car. You will be asked to solve for different things. Please pay attention: the numbers may change from problem to problem since they are randomized. 3) If the rod is subjected to a constant couple moment of M = 840 N•m, and the engine of the car supplies a traction force of F=11•TN to the wheels, where t is in seconds, what is the magnitude of the angular impulse from the moment and the force to the car-rider system in kg•m2/s from t = 0 to t= 4.9 s? Your answer must include 1 place after the decimal point. 4 m M F Your Answer: Answer
Force are called concurrent when their lines of action meet in .A one point .B two points .c three points .D four points
The expression: "If the vector sum of the external forces on a system is zero, the total linear motion of the system ..." Complete the sentence with the best option that completes the expression: a) It is constant and the utility lies in that it does not depend on the detailed nature of the internal forces acting between the members of the system. b) It is constant and the utility lies in that it depends on the detailed nature of the internal forces acting between the members of the system. c) It is not constant and the utility lies in that it depends on the detailed nature of the external forces acting between the members of the system. d) It is not constant and the usefulness is that it does not depend on the detailed nature of the external forces acting between the members of the system.
1. Find: a. Type of force needed to cut a huge box into three pieces of small boxes. b. Solve for the force needed to apply in each small box with the given stress. Stress (MPa) Length (cm) Width (cm) Height (cm) First Box 100 20 20 0.10 Second Box 120 20 16 0.04 Third Box 80 20 7 0.15
4