The rotor of a turbine 15 kg in mass, is supported at the midspan of a shaft as shown in figure. The shaft rotates at 500 rpm and the rotor displaces by an additional of 0.01 mm. The eccentricity (e) of the rotor is (Assume simply supported shaft)

Q: ]means the repair work done to keep the system in good working condition.

A: It is required to fill the blank

Q: Convert 3 centimetres (cm) to millimetres (mm)

A: Given data: Unit = 3 centimetre Need to convert into millimetre.

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: An installer can work 63⁄4 hours each day at a worksite. The installer will need303⁄8 hours to do a…

A: Given Data⇒ Time for which installer can work at a site a dayt=634 hours Time needed to install a…

Q: Vrite a complete program to mill around the part. The endmill is .500 diameter, and yo nt to leave…

A:

Q: :The form milling from the following is

A: Option b is correct.

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how to determine the volume of a flour using scientific method.

A: It is very important to measure the volume of the flour when any recipe is prepared in the kitchen.…

Q: さutてosuう +1 U、ズX ) Given. find dd.? dx

A:

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: A gas is under pressure of 40 bar abs at 40°C. a. Compute the pressure in kPa b. Compute the gage…

A:

Q: - Compute A.P.F. for F.C.C.?

A: APF is just the volume of the atoms within the unit cell, divided by the total volume of the unit…

Q: a) What is the reading (degrees, minutes)? b) What is the reading (degree and fractions of a…

A: Reading on main scale = 90 degreeReading of vernier matching with main scale = 22Least count of…

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: can you give me step by step how you filled out the chart

A: We have,Since, quality of steam is lies between 0 and 1, hence the phase of water is a mixture of…

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: A part may be properly represented on an engineering drawing with as few views as: A. one B. two…

A: Please find the answer in the next page.

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: The hand writing is not very clear :(

A: Basically the miller indices are the set of numbers which define the particular plane in the crystal…

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: where did you get 0.157

A: Given:Figure with dimension is providedTo find:Percent reductions in areaPercent reduction in area…

Q: The output of a certain machine can be increased if it undergoes a major overhaul now and it will…

A: P = $20,000 (P/A, 15%, 5)    = $67,044 finding A when given F, Given a future sum of money, F, how…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: A diesel engine in a power plant has an output of 150 KW at 260 rpm. It uses fuel oil having a…

A: Given data: Diesel engine power output = 150 kW @ 260 rpm Calorific Value of Fuel oil = 43912 kJ/kg…

Q: To make 5 cast iron tool holder as shown in Figure 2 on a one time order, and the inside hole…

A: Die casting and forging involves huge initial machine cost , it is not recommended to go for die…

Q: EX6:write a program read any vector and print the odd number only?

A: Note: Here you didn't mention any programming language so we are creating the program in the C++…

Q: Problem 7 Trekking handlebars or "butterfly bars" are popular with long-distance cyclists because…

A:

Q: How did you find the value of Patm of value 101.325?

A: How did you find the value of Patm =101.325 kPa?

Q: 1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you…

A: Given :    To find : instantaneous velocity v when t =4 s

Q: C. A certain manufacturing firm measures % in. by 1% in. on a map with scale 1:8,000. What is its…

A: For solution refer below images.

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: A specialty coffeehouse sells Colombian coffee at a fair rate of 300 kilograms annually. the beans…

A:

Q: An aluminum plate 20 feet by 40 feet is to be divided by 32 equal pieces 5 feet x 5 feet plate by…

A:

Q: A flow shop consists of 3-Machines on which 4-Jobs have to be scheduled in a fixed sequence. The…

A: Given:To find:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.