The ring at B is supported in equilibrium by spring AB, a cable running through the frictionless pulley at C, and cable BD. The pulley radius is 0.0180 m, and the unstretched length of spring AB is 0.24 m. If F₁ -350 N and F₂-140 N at 0=34 degrees, determine the spring constant and the force exerted on the ring by cable BD expressed in Cartesian components. a b С d C 0.120 m 0.180 m 0.0720 m BD D Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 0.400 m Note the figure may not be to scale. B N/m www F₂ A N

The ring at B is supported in equilibrium by spring AB, a cable running through the frictionless pulley at C, and cable BD. The pulley radius is 0.0180 m, and the unstretched length of spring AB is 0.24 m. If F₁ -350 N and F₂-140 N at 0=34 degrees, determine the spring constant and the force exerted on the ring by cable BD expressed in Cartesian components. a b С d C 0.120 m 0.180 m 0.0720 m BD D Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 0.400 m Note the figure may not be to scale. B N/m www F₂ A N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Do correctly please
I need answers for problems 7, 8, and 9 pertaining to the print provided.
I need help matching the following terms to the phrase it describes. Answers are used only once.
ANSWER FAST
Needs Complete and correct solution don't use chat gpt or ai i definitely upvote you. thank you.
PLEASE ANSWER ALL OF THE GIVEN QUESTIONS. Choose from the given choices/options below the question. I will rate you with “UPVOTE/LIKE” if you answer all of the questions. I will rate you with “DOWNVOTE/DISLIKE”, if you don’t answer all of the questions. THANK YOU FOR YOUR HELP.
Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions are: screw jack is lifting 3.2 tonnes, screw pitch is 12 mm, diameter of the screw is 5 mm. Coefficient of friction was not given but I think we will need it for total force calculation, lets take it 0.2. a) Calculate horizontal component to move the load - what is ment here by horizontal component? b) Calculate vertical component to move the load - what is ment here by vertical component? c) Total force needed to move the load with a lever of 0.82m d) Velocity ratio (VR=distance by effort/distance by load) Distance by effort (lever)=2 x 3.14 x 0.82 = 5.15m Distance by load = pitch= 12mm= 0.012 m VR=5.15/0.012= approx 429. e) Calculate efficiency. For this we need to have MA (mechanical advantage). It can be calculated when we know total force. Efficiency=Load (3200 x 9.8) / effort
Can you give me an example of laying out compound curves, please include explanation for each process/procedure of the solving.
Q5: For the below shaded area, calculate Ixand Kx 130 mm 30 mm 30 mm -40 mm -40 mm-
1.) Water backs up behind a concrete dam as shown in the figure. Leakage under the foundation gives a pressure distribution under the dam as indicated. If the water depth, h, is too great, the dam will topple over about its toe (point A). Base on a per unit length analysis of the dam with specific weight of the concrete as 150 lb/ft³, determine the maximum water depth for the following widths of the dam. L = 30 ft. Water 80 ft Water h,= 10 ft PA= yh Pg=yh
I need the answer in15 mints please please please best wishes Ahmed
F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.