The rigid block of mass M is supported by the three symmetrically placed rods. The ends of the rods were level before the block was attached. Determine the largest allowable value of M if the properties of the rods arc as listed (sigma w, is the working stress)

Q: the state of stress at points A and B, and show the results on a differential elements located at…

A:

Q: Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a…

A:

Q: Horizontal plates are connected to the bar AB whose length varies linearly from zero to HA, as…

A:

Q: 5. A steel tube and an Plates and an axiad Compressive force P pelied. Find the magnitudes ot forcas…

A: Axial compressive force P=-21 kN orP=-21×103 NAsteel=2AAlEsteel=3EAl

Q: Two loads P act as shown, one parallel to x and another parallel to z axes; each load P equals 1850…

A:

Q: The cross-sectional area of bar ABCD is 500 mm?. Determine the stress in segment BC. 40 kN 35 kN 20…

A:

Q: 2 m hollow cast iron pole has an outside diameter of 250 mm and a thickness of 10 mm. The pole is…

A: Given Data P=15 kN D=250 mm t=10 mm

Q: In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is…

A: Given data: STEEL…

Q: of 3.0 mm is produced at the tom of the groove. Compute the maximum stress in the rod y axial…

A:

Q: :For the two frame member shown F = 40 kN- Diameter of bolt = 10 mm- %3D Determine the horizontal…

A:

Q: The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force…

A:

Q: Determine the magnitude of the force (in N) of the x-component of the internal pin at E.

A:

Q: The force P is applied on the top of the solid cylindrical body which rests on a circular cap as…

A:

Q: Determine the uniform cross-section of the truss members BC, BE and AE, if the allowable stresses…

A: Given:Allowable stress for tension, σT=150 psiAllowable stress for compression, σC=125 psiForce,…

Q: Determine the stress in member CE assuming that the area in steel is 24 mm^2 p= 5 kN 3m 2m 2m 2m

A:

Q: Determine the vertical displacement of joint C of the steel truss shown inFig. a. The…

A: Answer : Given dimensions cross-sectional area of each member is A = 400 mm2 and Est = 200 GPa.

Q: A bar with an allowable tensile stress of 16 ksi has two holes at A and B. Determine the maximum…

A:

Q: The boom is supported by the winch cable that has an allowable normal stress of allow = 24 ksi. It…

A:

Q: A clamped edge steel diaphragm of radius 100 mm and thickness 3 mm is subjected to a uniform…

A:

Q: An object weighing 40 N is drop from a height of 4 m and hits a vertical steel rod on top. Determine…

A: Weight of object = W = 40 NHeight of drop = h = 4 m = 4000 mmDiameter of rod = d = 4 mmLength of rod…

Q: 3. Determine the horizontal AND vertical displacements of joint B using energy method. All members…

A:

Q: A clamped edge steel diaphragm of radius 100 mm and thickness 3 mm is subjected to a uniform…

A: As per given question A clamped edge steel diaphragm of radius 100 mm and thickness 3 mm is…

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: Determine the maximum value of the force P (kN) that can be applied to member AD if the allowable…

A: Given data: - The force applied at point A is P. The force applied at point B is FB = 12 kN. The…

Q: The rigid bar AB and CD are supported by pins at A and D. the vertical rods are made of aluminum and…

A: Given Data For bar AB L=4 ft A=0.75 in2 E=10×106 psi   For bar CD L=5 ft A=0.25 in2 E=12×106…

Q: If the gap between C and the rigid wall at D is initially 0.08 mm, determine the support reactions…

A: Given data: Deformation, δ=0.08 mm The value of, P=500 kN Young modulus, E=200 GPa. Calculate the…

Q: The tee shape shown is used as a short post to support a load of P = 1670 Ib. The load Pis applied…

A:

Q: A link in a mechanism is made from round bar. Due to the loading condition, the link is subject to a…

A: Maximum stress is 67 MPa Minimum stress is -27 MPa Required: Stress ratio (R)

Q: The fabricated steel members are being assembled into a truss on-site in the municipality of…

A:

Q: The homogeneous bar AB weighing 2000 lb. is supported at either end by a steel cable. Calculate the…

A:

Q: Problem 2: Determine the stresses in members CE, BD, and DE. Each member has an area of 1150 mm².…

A: A plane truss given with loading condition Area A=1150mm2

Q: 4. Given the beam loaded as below, label the stress blocks for points A and B. A A

A: Given

Q: The composite bar is firmly attached to unyielding supports. Compute the stress in each material…

A: Given P = 320 kN = 320 X 103 N To find Stress of each materials

Q: Show that for an annular rotating disc, the ratio of the maximum hoop stress to maximum radial…

A:

Q: Statics

A: Given Case 1 Angular distance = 4 km Horizontal distance = 5km Angle = 60o Case 2 Load = 50 N Angle…

Q: The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and…

A:

Q: 1.25 ft Determine the maximum allowable weight of passengers on the gondola ride which is suspended…

A: Given, σallowable=18 ksisquare solid steel = 1.5"

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: To find: The stress in the rods. Given: The young modulus of steel is Esteel=205 GPa and Ecopper=100…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.