The rigid bar AD is supported by two steel wires of 1/16 in. diameter (E = 29 x 10€ psi) and a pin and bracket at A. Knowing that the wires were initlally taut, determine (a) the additional tension in each wire when a 220-lb load P is applied at D. (b) the corresponding deflection of point D. F 8 in. E 10 in. A B D 12 in. 12 in. 12 in. Answer for (a), PeE = Ib, PCF = Ib Answer for (b), ôp = inches (magnitude only) Note: use up to 3 significant figures

The rigid bar AD is supported by two steel wires of 1/16 in. diameter (E = 29 x 10€ psi) and a pin and bracket at A. Knowing that the wires were initlally taut, determine (a) the additional tension in each wire when a 220-lb load P is applied at D. (b) the corresponding deflection of point D. F 8 in. E 10 in. A B D 12 in. 12 in. 12 in. Answer for (a), PeE = Ib, PCF = Ib Answer for (b), ôp = inches (magnitude only) Note: use up to 3 significant figures

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1-calculate the stress in the wire and the vertical deflection of point B using the given Information: d. fc 4m 16kN 8m gat steel Wire t B +
3/98 Each of the three uniform 1200-mm bars has a mass of 20 kg. The bars are welded together into the configura- tion shown and suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to the x-z plane. Compute the tension in each wire. B 600 mm 1200 mm A 30⁰! 1200 mm PROBLEM 3/98 600 mm -y
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
Determine the Vertical Deflection at the hinge. The elastic curve may be right or wrong. Indicate the negative sign if the answer is downward Determine the Vertical Deflection at the hinge 1O Kt E 29X103 Ksi I= 80 in4 5 k 6K O-8T internal hinge ー.2エ 3'
Question #4: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and Eb = 105 GPa, determine (dsteeF 40 mm, dbrass = 30 mm) 1- The reactions at A and E. 2- The deflection at C. 180 B 120 * 60kN 100 100 40 RN D Steel Brass Dimensions in mm.
> A Pinned- T -15 ft- 2 k/ff V V Roller утв -6ff- EI = Constant E = 29,000 ksi I = 3,500 in 4 Find: Maximum Vertical Deflection in the beam Method Ć unsupported joint using conjugate beam 2/9
What is the deflection at the hinge for the beam shown below? А C I В I L/2- - L/2
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
3. The cantilever timber beam is loaded as shown. The Use E = 10 GPa. Determine the smallest value of h so that the maximum deflection is not to exceed 10 mm. (Ans: h = 114mm) 1.5 m -1.5 m 120 N/m 50 mm h
回の at D ana Pa at all 400 MPa of 3.0 is 4.0 m рe aplied nd the pin Q9. Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Knowing that the magnitude of P is 4 kN, determiñe (a) the value of Q so that the deflection at A is zero, (b) the corresponding deflection of B. 20-mm diameter 0.4 m 0.5 m 60-mm diameter 2.
/stemezcom Lec3 working stres For the beam shown below, determine the concrete and steel stresses at the locations of the maximum positive and negative moments, Use ſ'c = 25Mpa. The answers are MPa, MPa, MPa and MPa. 3okN/m 8m 1m 4-25mmØ- -Top bars -4-16mmØ 250 250 bottom bars 630 630
4 Determine the design angle 8 for connecting mem- ber A to the plate if the resultant force is to be directed vertically upward. Also, what is the magnitude of the re- sultant? F₁ = 500 N -00 00 y ooo B FB = 400 N X