The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horizontal and the rods are stress-free. Determine the stress in each rod if the temperature of the rod at A is decreased by 40°C. Neglect the weight of bar ABC. Use a-10.7 x 10°C and E-200 GPa for steel. (

Q: (F al st al 2 m A E 0.75 m0.75 m 0.75 m 0.75 m' P' 2P

A:

Q: -30-mm diameter 250 mm -50-mm diameter 300 mm C

A:

Q: "he tensile stress-strain curve of a polymer may be represented by o=a rue stress and e is the…

A: Given: from the stress strain definition we have to remember the concept  concept for stress strain…

Q: : Determine the state of stress at point A on the cross section of the member at section a-a. 600 N…

A:

Q: 2-A teel pod is sfreteked between fwo rigid walls ard carries a tensile Coad f GO00N at C.f the…

A:

Q: copper tube with wall thickness of 8 mm must carry an axial tensile load of 175 kN. The allowable…

A:

Q: A torsion member is fabricated fror concentric thin tubes. At the ends, the are welded to rigid…

A: Given data: Inner radius = r outer radius = 2r shear stress in outer tube = τ

Q: The two vertical rods attached to the light rigid bar are identical except for ength. Before the…

A:

Q: 0,3in 0.4in2 3P 2P + C. Find the albwable säfe p if the stresses in the bar are the following: AB 50…

A:

Q: Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPA,…

A:

Q: Note: Dont truncate the solution Find the absolute value of the axial stress in member AC and BE of…

A: To find stress in member AC, BE

Q: Problem # 3: The steel bars are firmly attached to rigid supports. Initially the temperature is…

A:

Q: Two members, 1 and 2, are subjected to thermal stress. Determine the total deformation of member 1…

A: There will be compression stress in both bars.

Q: Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a…

A:

Q: answer asap

A:

Q: The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is…

A:

Q: The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal…

A: Given Data Three suspender bars are givenCross-sectional area A=450 mm2Young's modulus E=70 GPaTwo…

Q: A

A:

Q: The temperature of the cylindrical rod is heated to 45°C which is fixed in between A and C rigid…

A:

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A: To find deformation at point C

Q: Q- A stepped steel shaft is subjected to a clockwise torque of 10 Nm at its free end. Shear modulus…

A: Given- Clockwise torque T=10 NmG=80 GPa=80×103 N/mm2Strain energy in the shaft needs to be find out.

Q: The C83400-red-brass rod AB and 2014-T6-aluminum rod BC are joined at the collar B and fixed…

A: Given Data : Cross sectional area of each section = 1.75 in2 To Find :

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A:

Q: Part A shown construct an equilibrium equation that relates the axial load in the steel and…

A: Uniform distributed load, Length of all post, Diameter of steel post, Diameter of aluminum post, To…

Q: (a) Determine the magnitude of load P that can safely be applied to the structure if a minimum…

A:

Q: (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 142 (kips) is applied. The…

A: Given Data: The load applied on the beam is, P=142 kips   To Determine: The stress in the aluminum…

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1- Yes when normal stresses are maximum or minimum, then at that element shear stress is zero. 2-…

Q: The maximum tension in the INwer link of a Porter governor is 580 N and the maximum stress in the…

A: Given data in question  Stress Load To find out  Diameter

Q: Due to the applied loading, the element at point A on the solid cylinder is subjected to the state…

A: Considering the figure: σx=-12 Ksiσy=0ζxy=6 Ksi   The Mohr circle will be as follows:

Q: Knowing that each rod is solid and has a d twist (a) at B, (b) at C. A m - Brass B Aluminum m C 100…

A:

Q: bronze rod. Axial loads are indicated. Find the maxim exceed a stress of 80MPa Mpa in bronze. -1.0m…

A:

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A:

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: The steel used for the step shaft has an allowable shear stress of Tallow radius at the transition…

A:

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm. square cross-…

A:

Q: The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal…

A:

Q: Value of effective stress at point C

A: Given data : Dry unit weight γ=16 KN/m3 Saturated unit weight γSat=20 KN/m3 Unit weight of water…

Q: The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and…

A:

Q: The rigid bar of ABCD of negligible weight is supported hinge at A, steel rod at B and bronze rod at…

A:

Q: Determine the maximum tensile and compressive stress in the beam. 1600 lb 4000 lb 7 in N.A. 2 in 3…

A: Determine the maximum tensile and compressive stresses developed in the beam

Pressure and Stress