The reinforced concrete beams of a floor system arespaced at 8 ft on-center and are supporting a floordead load of 50 psf and a live load of 80 psf. Thespan of the beam L is 20 ft.Assuming that the beams are simply supported onthe building columns, determine:a. the factored load in lbs/ft that each beam mustsupport;b. the factored shear force diagram in each beam;indicate the amplitude and location of the maximumfactored shear force; indicate also your signconvention;c. the factored bending moment diagram in eachbeam; indicate the amplitude and location of themaximum factored moment; indicate also your signconvention.2011.0M TM8 ftSpan of Beam, L48 ftW.L12di giorni awoda oal NO.1 bna 30.10

Given : Reinforced concrete beam of a floor system spaced at 8 ft Dead load = 50psf Live load = 80…

The reinforced concrete beams of a floor system are spaced at 8 ft on-center and are supporting a floor dead load of 50 psf and a live load of 80 psf. The span of the beam L is 20 ft. Assuming that the beams are simply supported on the building columns determine:

The reinforced concrete beams of a floor system are spaced at 8 ft on-center and are supporting a floor dead load of 50 psf and a live load of 80 psf. The span of the beam L is 20 ft. Assuming that the beams are simply supported on the building columns determine:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The uniform distributed load (dead+live) for the building below is 120 psf. Calculate force transmitted by Gl into column C2. Draw free-body diagrams for all beams and girders involved in calculating this load. 8' 12' G2 C3 OPEN B1 B2 G1 G3 вз G4 8
. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support
The service load bending moments on a beam are 58 kip-ft for dead load and 38 kip-ft for live load. The beam is 10 in. wide, f ′c is 3000 psi, and fy is 60 ksi. Determine the depth of the beam and the tensile reinforcing required.
a reinforced concrete column of 300mm dia contains 4 bars of 22mm dia. find the total load, the column can carry, if the stress in steel and concrete is 50MPa and 3MPa respectively.
Answer asap
A small balcony constructed of wood is supported by three identical cantilever beams (see figure). 4b 3 Each beam has length L, = 2.1 m, width b, and height h 4b The dimensions of the balcony floor are L, x L2, where L, = 2.6 m. The design load is 6.1 kPa acting over the entire floor area. (This load accounts for all loads except the weights of the cantilever beams, 3 which have a weight density y = 6.1 kN/m3.) The allowable bending stress in the cantilevers is 12 MPa. Assuming that the middle cantilever supports 50% of the load and each outer cantilever supports 25% of the load, determine the required dimensions b and h (in mm). b = mm h = mm
Plss, i need the answer immediately. Consider a two-bay building frame ABCDEF, with A, B, and C as fixed supports, AD, BE, and CF as columns, and DE and EF as girders. Span DE is 5.9 meters long and span EF is 6.8 meters long. The columns have a height of 10.5 meters. Assume that the columns have same cross-sections. A wind-induced lateral load of 80 kN is applied at D, pointing towards the structure. Additionally, a-wind induced uniform load of 1.5 kN/m, pointing upwards, is applied at the girders. (a) Draw the free-body diagram of the structure.