The rectangular plate is subjected to the deformation shown by the dashed line. The dimensions are X=130 mm, Y=160 mm, and Δy=3 mm.   Determine the average shear strain in the plate at point A. Express your answer to three significant figures. Determine the average shear strain in the plate at point B. Express your answer to three significant figures.

Q: In (Figure 1), σy Figure = 49.1 MPa. Determine the principal stresses. Specify the orientation of…

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure below…

A: Given Original diameter of specimen=12.7mm Gauge length =50.1mm From the graph Young's modules=…

Q: Assume if the shear stress in steel exceeds about 4.00 x 108 N/m² the steel ruptures. (a) Determine…

A: The shear stress in steel is, S=4.0×108 N/m2   The diameter of the steel bolt is, D=1.25 cm   The…

Q: A 1.6 x 10-3-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.2 x…

A: Yyty

Q: essive strength of 140 MPa. a) What is the effective cross-sectional area of the femur in a human?…

A:

Q: 1. A frame ABC shown in Figure 2 consists of a tension member AB and a compression member BC. Member…

A: Given that  Mdulus of elasticity,E=200 GPa=200×109Pa Horizontal force,H=150 kN=150×103N Length,L=3.5…

Q: The rectangular plate is subjected to the deformation shown by the dashed line. The dimensions are X…

A:

Q: Part A In a materials testing laboratory, a metal wire made from a new alloy is found to break when…

A:

Q: Problem 2. From the given section of a wide flange shown in the figure, it carries a vertical shear…

A:

Q: A hollow bar with an outer diameter of 25 mm and an inside diameter of 18 mm carries a tensile load…

A: Tensile load = 100kN Outer diameter D1 = 25 mm inner diameter D2= 18 mm

Q: A steel music wire (Gage No. 32 with a diameter of 0.090 in.) is employed to support an axial load F…

A:

Q: nd trim printed circuit sheets. For the position shown, determine the vertical component of the…

A: Px = 390 sin 13 = 87.73 NPy =390 cos 13 = 380 N(FBD)x =2510034 FBD(FBD)y =9710034FBD

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

A: Given: εx=0 μεεy=350 μεγxy=210 μrad -45o≤θp≤+45o

Q: If F = 69 N, determine the internal normal force, shear force, and moment at points D and E in the…

A: An object that passes through a surface is prevented from passing through it by the normal force…

Q: A steel rod 250 mm long is subjected to a tensile stress. If its change in length is 1/40 mm, what…

A: Given: Steel rod length, L=250 mm Change in length, ∆L=140 mm Steel Young's Modulus, γ=2×105 N/mm2…

Q: Assume if the shear stress in steel exceeds about 4.00 x 108 N/m² the steel ruptures. (a) Determine…

A: We know thatstress=FAWhereF=Force appliedA=Area on which force applied

Q: The 530-lblb load is applied along the centroidal axis of the member. (Figure 1) PART A) Determine…

A: Given:-

Q: A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and…

A: Given: Lx=4 inch Ly=3 inch Lz=4 inch Fx=48 kips Fy=-60 kips Fz=54 kips

Q: PROBLEM 4. A piece of rubber, which was originally a square shape, has been deformed into a shape…

A:

Q: The principal forces at a point p of an elastic body are o(¹)=50N/cm², o(2)=-50N/cm² and…

A: The first principal force is The second principal force is The third principal force is

Q: Suppose that a 6-mm diameter steel has a breaking stress of 5.5x108 Pa. What will be the diameter…

A:

Q: Masses m and 2m are joined by a light inextensible string which runs without slipping over a uniform…

A: To solve this problem, we'll start by defining the generalized coordinates and the Lagrangian…

Q: 1. This graph is a stress-strain diagram that is of the type often studied by mechanical engineers…

A: We need to find the physical meaning of the area under the stress-strain curve.

Q: Two triaxial tests were performed on two prepared samples of the same slightly altered granite. At a…

A: Two triaxial tests were performed on two prepared samples of the same slightly altered granite. At a…

Q: Q1. An experiment was conducted in order to find the fracture toughness of a composite material. The…

A:

Q: A large 3.00x104 L aquarium is supported by four wood posts (Douglas fir) at the corners. Each post…

A:

Q: Problem 1: A cold drawn C-1025 steel rod of circular cross section is subjected to a variable…

A:

Q: Question 2 In a mechanical lab, a tensile test was performed on a rod of alloy having an original…

A: Consider the given data as below. Original diameter, Do=22 mm=0.022 m Original length, Lo=100 mm=0.1…

Q: A bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter.…

A: Hey dear I have solved for strain and modulus of elasticity. Have a look

Q: A material with a rectangular cross-section of 5 mm by 10 mm is loaded in tension with a force of 16…

A:

Q: A compressive force of 6,485 N is applied to a bone that has an outside radius of 2.5 cm and a…

A:

Q: ID 5t1 5t Part A Determine the negative bending moment at A with the maximum magnitude. Express your…

A: The force which applied to any material to cause deformation or bending along the plane or parallel…

Q: An axial load Pis applied to the rectangular bar shown. The cross-sectional area of the bar is 216…

A: Answer: Normal stress,  σ =2.73×108 N/m2 Shear stress,  τ =1.51×108 N/m2

Q: A square slab of a concreate road with thickness of 0.2m and 1.0m long experiences shear strain…

A: We have a square slab of thickness x=0.2 m and length y=1 m which is displaced by a distance…

Q: Find the internal load of each section of the bar due to the loading shown. Alsofind the maximum…

A: Solution:-Given thatthickness of the bar (t)=0.5 in

Q: Between AB there is a 20 cm aluminum wire that supports a mass of 490 g and between BC another…

A: To solve the problem depicted in the image you've provided, we will apply the formula for elastic…