The rectangular piece of wood, 56 mm by 183 mm, is used as a compression block. The grain of the wood makes a 32.3° angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 11.7 MPa for compression. Round off the final answer to three decimal places.

The rectangular piece of wood, 56 mm by 183 mm, is used as a compression block. The grain of the wood makes a 32.3° angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 11.7 MPa for compression. Round off the final answer to three decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

List of atest top ten websites used for social media.
In less than five sentences, briefly respond to these queries using your own thoughts and word. 1) Define active fire protection system and its importance in a building.
Directions: You are an architect in a construction company. You are tasked to build 3 circular water tanks for a 3- start hotel. You have to design the specifications of the water tanks, specifically the diameters and length of the tanks that could hold 10000 m2, 9000 m², and 8000 m²of water. You are required to write a proposal to the company board in two weeks. The board would like to see the concept used; it's practically, accuracy of computation and the organization of the report.
Prepare short answer please short explanation
I need a clear and fast answer within 20 minutes. Thank you
As described in the Data and Results part of , all tables and graphs must have descriptive information such as titles, column or row headings, units, and axis labels, and data points must be clearly marked. All figures must be numbered and have a descriptive title. The figure number and the title should be placed below the figure. All tables must be numbered and have a descriptive title as well. However, for tables, the table number and the title should be placed above the table. The relationship between a spring force and its deflection is given in the table at the top of the next column. Plot the results using engineering paper and incorporating the ideas discussed in this chapter.
What is the relationship between mass flow rate and volume flow rate?
UPVOTE WILL BE GIVEN. PLEASE ANSWER IN PARAGRAPH FORM (TYPEWRITTEN). ANSWER ALL THE SUBQUESTIONS. Research about AUTOCAD. a. meaning/definition b. proponents/inventors of autocad c. history of autocad
I have been asking this question for the third time. please give neat and clean answer. DOnt do shortcuts we paying money mor each question. ONLY TYPED SOLUTION WILL BE ACCEPTED ELSE MANY DISLIKES FROM ALL MY FRIEND INCLUDING THE PREVIOUS ANSWERS. 1st: https://www.bartleby.com/questions-and-answers/77kx-m-98.97-fn-9.cm-64m-88fn-8m-8m-88-kn-m-3/365c8b23-b4f3-446e-b18f-6fad1d17fd61 2nd: https://www.bartleby.com/questions-and-answers/77kx-m-ans-9.cm-64m-77-kn-m-98.97-kn-34.035-kn-98.97-kn-6.6-133.73-kn-16-88n-8m-8m-88-kn-24-88-kn-m-/7c90f342-276f-48d3-bb99-8d38ee6b07a8solve the indeterminate structure using moment distribution method.
The Administrator or a representative may request to see: O Any photo identification. The remote pilot in command's remote pilot certificate. A record of recent flights, such as a logbook.
As described in the Data and Results part of , all tables and graphs must have descriptive information such as titles, column or row headings, units, and axis labels, and data points must be clearly marked. All figures must be numbered and have a descriptive title. The figure number and the title should be placed below the figure. All tables must be numbered and have a descriptive title as well. However, for tables, the table number and the title should be placed above the table. Create a table that shows the relationship between the units of mass in kilograms and pound mass in the range of 50 kg to 120 kg. Use increments of 10 kg. Present your work incorporating the ideas discussed in thischapter and using engineering paper.
hi, show your solution. thank you so much for helping me.