The recessed rectangular gate is located at an angle of 45 to the water surface. The gate is 5 m wide and 1.5 m high. The gate is used to control the flow of water. The bottom of the gate is 10 m deep. At point "A" is the hinge. Determine the force to be applied at point "B" which is normal (90 degrees) to the gate to open it. Ignore the weight of the gate. Complete the drawing. 45° 10 m A F. 1,5 m B.

Q: Determine the equation of the influence line for the reaction at A in the continuous beam shown in…

A: By Muller Breslau method, As we have to find the reaction at end A, hence Support at A will be…

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: Find the domains of: f(x)=- x - 9 a. {x\x€R, x#9} b. {x|x€R, x#-3, x#3} c. {x|x€R, x+-3, x # 3, x #…

A: Hello dear this is the solution of your problem The answer is found to be Option (b)  For…

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: +y") dx ly

A:

Q: PROBLEM 2: Determine Ix and Tx.

A: given- a plane figure to find- M.O.I  about X-axis and centroidal axis.

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: -0129 -077 R26

A:

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: Y

A:

Q: * .I don't like this," said Ali“ Correct Incorrect

A: The correct punctuation marks for this be like this "I don't like this," said Ali.

Q: 350 mm 250 mm 600 mm Member Magnitude,N X-component Y-Component 180 mm 360 mm G H TBD 240 mm 400 mm…

A: Given- A frame structure is given    To find- forces at joints G H E and Tbd

Q: 500 50 60 400 500 50 80 - 340 80

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.