The ratio of the torsional moments of resistance of a solid circular shaft of diameter D, and a hollow circular shaft having external diameter D and internal diameter 'd' is given by (a) DA -d* D4 - d* (b) D4 D³ – d³ (c) D3 D3 (d) D3 - d3

Q: Given traffic flows for each lane group at a T junction shown in Figure below. The saturation…

A: Critical lane volume for each phase: P1: 500, P2: 250, P3:150 Sum of criticial lane volume,ΣVc =…

Q: 13. - should be located to withdraw water from slig below the surface in order to avoid sediment in…

A: The intake structures are used to safe withdrawal of water from the source, which will be discharged…

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: QUIZ: Determine the reactions at the supports A and B of the beam shown in figure. 6 kN/m 3 kN/m

A: Free Body diagram of the given problem:

Q: Use the method of joints to determine the force in each member of the truss shown in the figure…

A: Let height be H43H+34H = 82512H = 8H = 3.84 Calculate Support Reactions ΣFY=0AY+CY = 20sin45°AY+CY =…

Q: 4. For the figure below, the specific gravity of unknown fluid equal to .. a. 0.59 b. 1.59 C. 99.11…

A: Equating pressure at datum…

Q: P1. Determine the distance x measured from the y axis to the centroid of the area of the iangle…

A:

Q: Q3) For the circular arch shown in the figure, compute the value of "P " such that the vertical…

A:

Q: Q1: A tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20…

A: Given that,  gage length = 50 mm diameter = 20 mm loat at 0.2% yield point = 100,000 N gage length…

Q: Solid Mechanics Set up the appropriate equation that is used to solve for the moment of inertia…

A:

Q: A- It is required to dewater a construction site, The bottom of the construction will be Im below…

A: Q= 645.52 m3/day

Q: 30 F2 = 300 N F1 = 250 N |3D 60° A 2 m -3 m- 4 m B F3 = 500 N Determine the moment of each of the…

A:

Q: The diameter of the horizontal storm-water pipe sloped at 1/50 and required to drain a rain water…

A: Lets select pvc pipe with mannings coefficient (n) = 0.012 A(Area of roof) = 5300m2 I (rainfall…

Q: Prob.7. Workout the depreciated replacement cost of a building having the following particulars by…

A: Given that, Total life of building(n)  = 80 years  Built-up area = 400m² Total life of building in…

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A:

Q: The figure below shows a simply supported beam with an overbang. The beam is made of two types of…

A: Allowable stress in pine=11 Mpa Allowable stress in plywood=14 Mpa Modulus of elasticity of…

Q: Q 7: It is required to project a horizontal circular curve that connects the first two roads AB and…

A: Horizontal projection of the curve  will be  equal to the length of the longest chord   AC

Q: From your graph, plotting the yield stress against 1/vd, you found that oo 69 MPa and k, = 0.8…

A:

Q: If n is the ratio of internal and external diameter of a hollow shaft, the ratio of the weight of…

A:

Q: Analyze the given continuous beam carrying UDL of 2.5kN/m using three moment equation. Take El as…

A:

Q: 2. Clockwise interior angles observed in a closed loop traverse is given below: A 83° 30' 251° 50' C…

A:

Q: Consider the velocity field given by u = and v =- 2xy. Find the circulation around an area bounded…

A:

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: 2- A rectangular channel with bottom width =8.0m, Manning roughness, n =0.01986, channel bed…

A: The flow area of the given rectangular channel is  The wetted perimeter of the given rectangular…

Q: need the answer quickly

A:

Q: Lor the beamshown in Fig.3, Compute the slop of the e latic curve at A and B Aned the oe flection at…

A: We shall apply equations of equilibrium for support reaction calculation,  ∑Fy =0 RA+RB= 12(5*1)+…

Q: A 180 mm diameter well witch penetrating in soil at depth 7 m to extrude the ground water from a…

A: A hydraulic pump is a mechanical source of power that converts mechanical power into hydraulic…

Q: If you know that the following plotting position formula applies only to data that have an…

A: As given the equation is: 4k+6k=9k Simplifying the equation above to calculate the value of k

Q: Three principal stresses of 250, 100 and -150 MN/m? act in a direction X, Y and Z respectively.…

A:

Q: 8.13 A polycarbonate sample showed a craze growth length and time relation- ship of e=k log(t/to).…

A: Following is the given relationship between the craze growth length and time of the polycarbonate…

Q: 8.1: Use the virtual work method to determine the horizontal and vertical deflections at joint B of…

A: Due to issue in Math type , providing handwritten solution

Q: Design the beam shown below for shear, it is subjected to a service live load of 40 KN/m and a…

A:

Q: F10-2. Determine the moment of inertia of the shaded area about thex axis,

A: step 1-

Q: I need a report on the spot speed measuring report includes .1 introduction 2. theoretical + Fig +…

A: INTRODUCTION: The speed of traffic on existing roadways has an impact on traffic flow. The geometric…

Q: Problem 16.1. Determine. · the deflection at point D of the beam shown below. El is By the moment-…

A: Moment Area Method- In this method the area of the bending moment diagrams is use for finding the…

Q: is impure tricalcium silicate is impure (C3S) and dicalcium silicate (C2S). * Tobermorite,…

A:

Q: Situation 10: A soil sample has water content of 25%, degree of saturation of 80%, and specific…

A: Given data : Degree of saturation (S)=80100=0.8Water content (w)=25100=0.25Specific gravity…