The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Power required to drive the plunger O 0.013 hp O 0.543 hp O 0.892 hp O 0.453 hp

The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Power required to drive the plunger O 0.013 hp O 0.543 hp O 0.892 hp O 0.453 hp

Name: The ram and plunger of ahydraulic press are 150 mm and25 mm in diamet
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The ram and plunger of ahydraulic press are 150 mm and25 mm in diameter respectively.With a plunger stroke of 30 cm,the press is able to lift a load of1 tonnes through 1.5 m in atimes of 25 min. Power requiredto drive the plunger0.013 hpO 0.543 hpO0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

..Consider a leather belt with the following given: width of 100 mm, thickness of 6.4 mm, velocity of 18.3 m/s. Which of the following is the centrifugal force across the belt? Note that the density of belt is approximately 974 kg/m3Group of answer choices 205 N 309 N 209 N 305 N
The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Area of the plunger Calculate 1-area of the plunger 2-N0 of stroke 3_area of ram 4_area of the ram plunger 5-power required to drive the plunger
3- If F = 1x, F = xi, a = wk,, the centrifugal force is equal to a: mw²xî ------- b: -mw²xk c: mw²x k a: 4 d: -mw²xî e: None of them Ś
A certain six-cylinder engine has a 130.2 mm bore, a 127 mm stroke, and a clearance volume of 0.119 L in each cylinder. Does the engine run on diesel or gasoline fuel? Explain your answer
Subject: Hydraulics A closedcylindrical vessel 5 ft in diameter and 6 ft high is 3/4 filled with molasses(SG = 1.24) and rotated about its vertical axis. Air is pressurized at 14.5psi. a. If w = 50 rpm, solve for thepressure at the base at the circumference of the vessel b. If w = 75 rpm, solve for thepressure at the base at the circumference of the vessel c. Solve for w (in rpm) so that thereis no water at the base of the vessel within 1.8 ft radius
When designing an impeller for a centrifugal pump, you would consider the following materials attributes. [M ten waaler vir 'n sentrifugale pomp ontwerp, sal jy die volgende materiaal eienskappe in ag neem.] O A. creep strength and density O B. hardness and chemical composition O C. toughness and stiffness O D. hardness and thermal expansion
: By Bligh's and Lane's theory For the hydraulic structures shown below calculate 1- Sketch the HGL from U/s to D/s 2- Fine the uplift pressure from at key point 3- Find the thickness of floor at point A&B 4m 15m 10m 10m 6m 8m 35 m
A double acting pneumatic cylinder has a diameter of 160 mm. The rod is 50 mm diameter and the stroke is 160 mm. It must produce a pushing force of 10 kN. The flow rate available in both dirertions is 14 mm³ /minute. Calculate: (c) (i) The needed system pressure (ii) The force of retraction (iii) The velocity on the extension (iv) The velocity of retraction (v) The power used on the outstroke (extension motion)
The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Area of the plunger 9.54 cm2 11.21 cm2 4.91 cm2 O 6.82 cm2 O
please answer again the image posted for formula can't be load.
S2-Q4: A gear pump has an efficiency of 80% runs at a rated speed of 90000 rev per hour. If the pump delivers 2.77 liters per second with internal and external diameters of 7.5 cm and 50 mm, determine the width of the pump gear.