A man uses a rod of length 5.0m to lift a 700 kg marble. The fulcrum is 0.50m from the end of the bar that is under the marble. Calculate the mechanical advantage and minimum effort required to lift the load. If the efficiency of this system is 90% determine it's velocity ratio.

Q: If a double-acting air cylinder with a 40-mm diameter bore and 200-mm stroke operates at 7000 kPa…

A: Given,  Diameter of the piston , d =40 mm Stroke length, L =200 mm. Cycle of operation ,N =30…

Q: A crate of mass 75kg is pushed along a floor with a force of 26N for a distance of 7 m. Calculate…

A: Find the work done .

Q: Drum Truck Design a truck that can be used for handling 55-gal drums of turpentine (7.28 lb/gal) one…

A: Given: The volume of the drums of turpentine: →V=55 gal And density of the turpentine: →ρ=7.28…

Q: If the diameter at section 1 is D₁ = 0.5 m, and at section 2 the diameter D₂ = 0.2 m. All the other…

A:

Q: A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 4 m² and a large…

A:

Q: 6) A screw jack is used to lift a mass of 500kg. The screw has a thread with a pitch of 8 mm. An…

A:

Q: A 3192kg car is going up the Amerat hill, at angle 16.8, with 2 people inside the car each of 49kg.…

A: Given, Mass of car =3192 kg Mass of passengers=2×49kg=98 kg Total Mass, m=3192kg+98kg=3290 kg Lift…

Q: . Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod…

A:

Q: 2. The pressure of a hydraulic working cylinder is intensified by using a pressure intensifier. The…

A:

Q: 2. A spherical object has a radius of 0.45 cm. The density of water is 1000 kg/m3. If the block is…

A: Given data as per question The radius of object =0.45 cm Density oof water =1000 kg/m3

Q: Find an expression for the centrifugal force Fc if it depends on the mass m, the angular velocity…

A:

Q: Problem# 5 Container is placed over incliced plare, it accelarate at 10 m/s2, will the water inside…

A: Write the expression of inclined angle of the container. tanβ=ag   Calculate the inclined angle of…

Q: . The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a construction…

A: Thickness = 3 mm weight = 200 N velocity = 2 m/s

Q: The hydraulic jack shown below consists of a master cylinder with a diameter of 60mm and a lifting…

A: To find: The force at location B to lift the weight off the ground at location A. Given: The…

Q: Fisher & Paykel top loader washing machine is used to extract the 20 kg of wetted and mixture…

A: Solution: Given Data: M=20 kgP=650 WN=1000 rpmm=5 kgr=0.6 mk=500 kN/m   To Find: TFC∆S

Q: Answer fully

A:

Q: plz plz help me nowwwwww  If the piston mass is 20 kg and the car mass with its base is 400 kg,…

A: Given: The mass of piston, m = 20 kg The mass of car with base, M = 400 kg The specific gravity of…

Q: Find the value of work done if force 2 N displace crate by 1 m

A: Given data : Force applied is denoted by=F Displacement is denoted by=d   To find : Work done

Q: . The hydraulic system of a backhoe is used to lift a load asshown in Figure 11.45. (a) Calculate…

A: To determine (a) The force that the slave cylinder must exert to support the load and the weight of…

Q: Compute the height to be raised of box to gain potential energy of 544 J having mass of box 23 kg

A: The height to be raised of box to gain potential energy of 544 J having mass of box 23 kg is h = 2.4…

Q: The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a…

A:

Q: A steel pulley with a mean rim radius of 120 mm is rotated at a speed of 1100 rpm. If the mass of…

A:

Q: An investment cost for the wind power system is RM 5000 with the annual maintenance costs are RM…

A: Given : D = 30 m P = 400 kWh v = 7.5 m/s ρ=0.602 kg/m3 To find : Efficiency

Q: A hydraulic press has a ram of 26 cm diameter and plunger of 6.5 cm diameter. How much weight can be…

A: According To Pascals Law, Pressure intensity at a point in any point is equal in any direction i.e,…

Q: height of 600 mm onto a closed coil compression spring which instantaneously compresses by 200 mm…

A:

Q: me I don't understa

A: given:

Q: 1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system…

A:

Q: An effort of 2 kN is required just to move a certain body up an inclined plane of angle 15°, the…

A:

Q: A spacecraft must be maneuvered through an angle of 6O-deg in 30 s. The spacecraft moment of inertia…

A: Thrust force is a type of force which helps the rocket in the air and space. the thrust force is…

Q: Given that the compressor's energy input is 2100 kJ and the heat provided is 3500 kJ. The area is…

A:

Q: Which produces the larger pressure, a 0.3m diameter foot of an elephant of mass 5000kg or 0.01m…

A: A vector is a physical quantity that has magnitude and direction both. A scalar is a physical…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.