Answered: The R.L. of the point 'A' which is on…

The R.L. of the point 'A' which is on floor is 100m and back sight reading on 'A' is 2.445m. If the foresight reading on the point 'B' which is on ceiling is 2.745m, the R.L. of point 'B' will be-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Find headlight sight distance and intermediate sight distance for V=70kmph. (Hint: f=0.36,t=2.5 s,…

A: Since Head Light Sight Distance is equal to the Stopping Sight Distance, SSD As per IRC,…

Q: A transit with a stadia interval factor of 99.89 was set at point C with elevation 452.35m and on…

Q: 31. a) Deternine the elevation at each stations. b) Difference in elevation between the 1+20 and…

A: Given profile levelling HI = height of instrument FS = fore sight BS = back sight IS = intermediate…

Q: Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the…

A: Given data: Instrument height, h = 1.5 m Length, l = 4 m slope of ground (down slope), tanθ=110

Q: Line Distance AB BC CD DE EF FG 62.56 29.49 65.07 41.14 43.70 26.74 Forward Bearing N 81-02-05 W N…

A: Given: LINE FB BB AB N 81-02-05 W S 79-26-30 E BC N 08-16-07 W S 13-18-15 E CD S 87-34-45 E…

Q: ➤ The following observations were recorded when carrying stadia level between two temporary bench…

A: First, we need to understand the problem and the data given. We are given the back sight, fore…

Q: The elevation of points O and a is 267ft, that of point is B and C is 52 4ft and that of D is 820ft…

A: The scale is defined as the ratio of the distance on the map to the distance on the ground. Scale…

Q: The backsight to a BM is 3.125 m and the FS from the same instrument set up is 3.625 m. If the…

A: Given Data, Distance from level to BM = 3850 m Distance from level to TP = 4714.05 mCalculate the…

Q: A level was set up in the middle of two pegs A and B and the staff readings were 2.015 and 1.895…

A: hA=2.015m hB=1.895m h'A=2.195m h'B=2.005m To find collimation error and reading on peg A

Q: figure, Calculate the reduced levels of the points by rise and fall method.

Q: 2. A pre-engineering baseline was run down a very steep hill as shown in Figure 1. The vertical…

A: Elevation : When a point's height is its vertical distance above or below the surface of a reference…

Q: A level was set up in the middle of two pegs A and B and the staff readings were 2.015 and 1.895…

A: To find collimation error

Q: A zenith angle is measured as 97°-55'-58" in the direct position. What is the equivalent "zenith…

Q: calculate the R.L.

A: Given: benchmark=432.384 To find: Fill level book and calculate RL of points

Q: 10 - convert angle 1.497 rad to degrees a) O 850: 55:48" b) 269o: 48':55* C) 850: 48':S5“ d) 269o:…

A: The conversion of radian to the degree is done by multiplying the factor 180π,

Q: A flag post was erected on the top of a building. If vertical angle subtended at bottom and top of…

Q: Use the following set of field notes to determine the average zenith angle of the set. Instrument @…

A: Average of Zenith angle = Sum of all angle/ no. Of angle

Q: The back sight reading on a B.M. = R.L. of 150 m was (-2.250 m). The erected staff reading on the…

A: Backsight reading on a bench mark = B.S = -2.250 mForesight = F.S = 1.450 mReduced level (RL) = 150…

Q: Three stations P, R and Q are along the same plane. Angle of elevation of the top of signal of…

Q: Profile Level Notes: The elevation of BM A = 343.43' BS (plus sight) on BM A = 9.43' IFS (minus…

A: Given The elevation of BM A = 343.43' BS (plus sight) on BM A = 9.43' IFS (minus sight) on STA 0+00…

Q: find the elevation of reduced level for all point For sight Reduced level Back sight point Inter…

A: Given that:

Q: Tabulate the computed values accordingly. Length, Calculated Bearing LATITUDE DEPARTURE UNE +N -S +E…

Q: 10. The known elevation of BMA is 625.00 ft. A 3-course closed circuit was set up and 5 intermediate…

A: Given Back sight and foresight at mentioned stations. Elevation of BM A = 635 ft To Determine…

Q: 1) Find, the unknowns ("aaa" through "Beg") in the table of closed traverse starting from BM and…

A: Rise and fall are the value equal to the difference in reduced levels between the two consecutive…

Q: Find headlight sight distance and intermediate sight distance for V=70kmph. (Hint: f=0.36,t-2.5 s,…

Q: IV - Coordinate measurement Oa) 1, II, II, IV OB) I, II, IV OC) I and III OD) I and II O TO) II and…

A: Brief concept- The image shown is of auto-level. This is used commonly in surveying for leveling…

Q: *The R.L, of the point A which is on the floor is 100 m and backsight reading on A is 2.455 m. If…

A: Using formula

Q: The following data was obtained with the level. What is the HI of the instrument Sta. BM ΤΡΙ TP2…

A: For first part of the question the HI can be calculated where BS is taken that is for first two rows…

Q: THE MAGNITUDE OF THE RESULTANT O TOTAL MOMENT ACTING ON POINT "A" TOTAL MOMENT ACTING ON POINT "B“ ο…

Q: A line of levels 12.4 km is run to check the elevation of BM2 which has been found to be 300.8855 m…

Q: Compute the elevation of BM6 a.270.17 b.207.71 c. 217.70

A: Given Elevation of BM5 And f.s and b s of all the stations

Q: The R.L, of the point A which is on the floor is 100 m and backsight reading on A is 2.455 m. If the…

Q: Compute the elevations of BM2? STATION BM 1 TP 1 TP 2 TP 3 TP 4 BM 2 BS 2.71 3.62 3.51 3.17 1.47 HI…

A: Given,

Q: A level was set up in the middle of two pegs A and B and the staff readings were 2.015 and 1.895…

A: To find collimation error

Q: in the two-peg of a dummy level, the following observation are taken. Rod Reading on A Rod Reading…

Q: Profile Level Notes: The elevation of BM A = 533.00' BS (plus sight) on BM A = 6.91' IFS (minus…

A: To Determine :- Elevation of the STA 1+50 Concept :- HI = Elevation + BS Elevation = HI - IFS…

Q: (plus sights) BS (+) Station HI BMA 6.87' 1031.19' TP1 4.98' TP2 7.43' TP3 0.98' TP4 4.57' TP5 8.20'…

Q: The following consecutive readings were taken with a level and a 4mt. leveling staff on a…

A: Given:- The height of the leveling staff = 4 m The readings are taken at continuous common interval…

Q: Which date below has/have the smallest amizuth angle (from true south) at 9am? 12/21 10/21 8/21 6/21

A: Brief concept introduction- Azimuth- It is the angle between the true north and the particular line…

Concept explainers

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.

Question

The R.L. of the point 'A' which is on floor is
100m and back sight reading on 'A' is 2.445m.
If the foresight reading on the point 'B' which
is on ceiling is 2.745m, the R.L. of point 'B' will
be-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

: Work out included angles from following data : Sr. No. Line F.B. AB 40° BC 120° CD 240⁰ DA 340⁰ 160' 1 2 3 4 B.B. 220' 300' 60' 1
Which one of the following surveying equipment is no longer in use? a. Auto level O b. Cross staff O C. Total station d. Dumpy level
I need part C only . Provide clear solution.
Complete answer
Engineer’s Transit was set at a horizontal distance of 175.24 meters from the base of a tower. The angle reads 280 45’ at the top of the tower. If the backsight reading from a reference benchmark of elevation 30.00 meters above mean sea level is 1.68 meters, find the elevation of the top of tower.
What is the back azimuth of a line has an azimuth 267°?
A level instrument at a height of 1.320 m has been placed at a station having a Reduced Level (RL) of 112.565 m. The instrument reads -2.835 m on a levelling staff held at the bottom of a bridge deck. The RL (in m) of the bottom of the bridge deck is A. 116.720 B. 116.080 C. 114.080 D. 111.050
What action should a topographer who has made measurements and markings in the figure below have done? R. Sin Bina (Ağec 7.80 kazık) 15 - 8.38 Telefon direği a) Rehearsal B) Solving OC) Jaloning D) Punctuation O TO) Connecting 12.45
Draw/ Illustrate the profile leveling The second photo is an example of profile leveling Thank you!
Surveying
) On a truly vertical aerial photograph, whose focal length is 100.00 mm, the base ofthe corner of a vertical building appears 50.00 mm from the principal point. The top of thesame corner of the building is measured to the 51.00 mm from the principal point. It has 2been determined that the flight altitude of the camera above the ground at the base of thebuilding is 8000.0 ft. What is the height of the building?
A tall tower was photographed from an elevation of foom above the datum. The radial distance of the top & bottom of the tower from principal points in the photograph are 112-5 mm & 82.4mm. If bottom of towes is at an elevation 250m above the dation then beight of the tower would be