please solve in 4o mins i will give you positive feedback tefrigerating and Air-Conditioning Engineers, Inc.Sea Level1010.00.7Fos0.81.0T-100Sensible heat5.0-20DH-1.0Total heat DH,5.0+as-20901204.080ofEnthalpyHumidity ratio1102525 wet hulb temperatuteEnthalpy (h) kikjoules per kilogram dry air10020.n temperah1640Saturation60%903040%20107010% relative humidityDry bulb tamperature "C90%80% Problem IIAn air-conditioning unit consists of a cooler with a condensate trap followed by a heater. Air at101.3 kPa enters (point 1) at 35°C, 70 percent relative humidity, and leaves (point 3) at 20°C, 50percent relative humidity. For a flow rate of 400 kg dry air per hour, (a) draw the process inthe psychrometric chart, state your assumptions and calculate (b) the amount of water removedper hour and (c) the heat added (in kJ/kg dry air) in the heating sector.Coeling coilHeating CoilAir2 CondensateTraptefrigerating und Air Conditioning Enginoers, Inc.Sea Level1001.0130tasSosite heatFotl heto110EthulyHhumalay atiowet hulb seapeEthulpy kikls per kikogram dey air40le humdty60Dry hulhmpeeC

Answered: Image /qna-images/answer/bbe811c2-9317-4641-840a-9f62091177e2.jpg

Answered: the psychrometric chart, state your…

the psychrometric chart, state your assumptions and calculate (b) the amount of water removed per hour and (c) the heat added (in kJ/kg dry air) in the heating sector.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am confused because on my homework i got marked wrong for this, unless I used to many sig figs.
Don't answer if you already answered this. If i see the same solutions, i'll downvote you. Follow the instructions. Typewritten for upvote. No upvote for handwritten. Thank you
Specific Instructions: Solve each problem NEATLY and SYSTEMATICALLY. Show your COMPLETE solutions and BOx your final answer. Express your answers in 2 decimal places. TOPIC: ENGINEERING ECONOMICS Problem: A company invest Php 100,000 today to be repaid in 5 years in one lump sum at 12 % compounded annually. If the rate of inflation is 3 % compounded annually, approximately how much profit, in present day pesos, is realized over the five years?
Please give me answer in half hour otherwise I wil report
Follow the instructions. Typewritten for upvote. No upvote for handwritten. Thank you
You change your tries to bigger ones that have a diameter of 35.3 inches based on the circumference from above if your speedometer said you were driving 45 mph what is your actual speed
Hi, Could you please help with this question, if you need to take more credits then please feel free. showing working out if possible too please, Thank you
Please answer immediately thank youuuu
How the actual temperature deviates from standard temperature, that if correction due to temperature is neglected will cause an error of of 1 part in 5000?
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
conceptual question, no calculations