The propped cantilever beam shown below has a length of 12 meters and is supported by a roller at A and a fixed support at B. The beam has a modulus of elasticity of E = 200 GPa and a constant moment of inertia | = 255(106) mm4. If the beam is subjected to a uniform distributed load of w = 15 kN/m, determine the following using the CONJUGATE BEAM METHOD: 1. Reactions at the supports A and B. 2. Slope at the free end. 3. Maximum deflection.

The propped cantilever beam shown below has a length of 12 meters and is supported by a roller at A and a fixed support at B. The beam has a modulus of elasticity of E = 200 GPa and a constant moment of inertia | = 255(106) mm4. If the beam is subjected to a uniform distributed load of w = 15 kN/m, determine the following using the CONJUGATE BEAM METHOD: 1. Reactions at the supports A and B. 2. Slope at the free end. 3. Maximum deflection.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.Determine the maximum compressive stress acting on the cross section. 2.Determine the maximum…

Q: The solid compound shaft made of three different materials carries the two torques as shown. (a)…

Q: A load of P = 95 kN is supported by a structure consisting of rigid bar ABC, two identical solid…

Q: 6. The uniform beam is supported at its ends by two springs A and B, each having the same stiffness…

A: Given ⇒ M = 50 kg T1 = 0.83 Sec. → for mass (m)When mass becomes (m+M)then…

Q: QAI For the frame shown in Figure QA1, using the Consistent Deformation Method: 1. State the degree…

Q: Draw the shear force and bending moment diagrams for the beam.

A: Hi! Thank you for the question As per the honor code, We’ll answer one question since the exact one…

Q: 5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C,…

A: Given Data Shear modulus (G) = 85 GPa Diameter of shaft (d) = 40mm Length of AB (LAB) = 0.5m =…

Q: Figure Q3 (a) shows an overhanging beam ABC subjected to a uniformly distributed load w along AB and…

A: yield stress of the material is 250 MPa

Q: 4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the…

A: Size of pieces = 50 × 200 mm

Q: Figure shows a statically determinate beam under distributed loading conditions where C is the…

Q: The shaft is hollow (outer diameter d, = 295 mm and inner diameter d, = 250 mm) and delivers 1,700…

A: Given Data: It is asked to draw the Mohr's Circle.

Q: use flexibility method

A: Step 1:Step 2:

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

Q: Example 6 Determine the support reactions on the frame shown. El is constant. 8 kN/m 5m Actual Frame…

A: The statically indeterminate frames are solved using the method of consistent deformation or Force…

Q: Figure 1 shows a rigid body supported by a truss system, all elements are pinned at both ends. If a…

Q: Determine the deflection at midspan

A: Uniformly distributed load (UDL): - It is a type of load that is applied into an object evenly…

Q: Draw the torsional moment diagram. Determine the torsional angle CA (rotation angle) that will occur…

Q: Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam…

Q: used to support the wood de Set a = 1.5 and b =4.

A: Given:- a=1.5 b=4 To find:- magnitude loading in kN/m

Q: A steel column of length 4.75 m forms part of a support structure and is subjected to an axial…

A: i)Slenderness ratio λ: It is defined as the ratio between effective length minimum radius of…

Q: Two rods, A and B, of equal free length are elastic. Both hang vertically 0.6m apart and support a…

A: Ad

Q: (2) (1) Pe с B L2 Li

Q: The truss is loaded as shown. 3.2 kN A B 3.0 m 3.2 kN 1.6 kN D 3.0 m F |-30 m- -3.0 m - Analyze it…

Q: 6 m 3 m 3m 30 kN 4 m F 4 m 4 m H. 4 m A B Figure (a)

A: Using method of joints to calculate the forces in each member of the truss. Support reaction at A=…

Q: A beam having the cross section shown is subjected to a couple that acts in a horizontal plane.…

A: z = 1.43 in ( from left side )z = 5 - 1.43 = 3.57 in ( from right side )Iy = 11.3 in4Maximum…

Q: 2. A beam is loaded and supported as shown. On a section 3 m to the right of support A, determine…

Q: A rectangular beam is supported at both ends. It carries two concentrated load of 30kN, a clockwise…

A: Note - value of reaction is taken as 256.738kN to avoid calculation mistakes.

Q: A beam fixed at both the ends is subjected to a uniformly distributed load w' on its right half…

A: Beam: Fixed at both ends.Load: Uniformly distributed load (UDL) on the right half of the…

Q: A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure). T >> r2…

Q: Figure shows a structure loaded with vertical load of 40 kN at joint C, horizontal Load of 20 kN at…

Q: A solid 27 mm diameter shaft is subjected to an axial load of P = 50 kN and a torque of T acting as…

Q: Figure Q3 shows a frame structure, which is fixed at A, D and F. The frame is subjected to the…

A: The given figure shows a frame structure, which is fixed at A, D, and F. The frame is subjected to…

Q: A propped 6 m long cantilever beam is shown in Figure 3. In addition to a saw-tooth loading as shown…

A: Given clockwise moment is applied at B = 10 KN-m

Q: Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b.…

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

The propped cantilever beam shown below has a length of 12 meters and is supported by a roller at A
and a fixed support at B. The beam has a modulus of elasticity of E = 200 GPa and a constant moment of
inertia | = 255(106) mm4. If the beam is subjected to a uniform distributed load of w = 15 kN/m,
determine the following using the CONJUGATE BEAM METHOD:
1. Reactions at the supports A and B.
2. Slope at the free end.
3. Maximum deflection.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem I. In a high-rise building construction, a boom is being used to efficiently transport materials from the ground to a certain level in the building. Shown below is a figure of the boom supporting the load P=223KN 100 mm 87.5 mm 2P 12.5 mm dia в -10 m- At the right is the support detail at B. a) What is the normal stress (in MPa) the boom is subjected to if its cross sectional area is 1174 mm² ? b) Calculate the shear stress in the pin (in MPa). c) If the allowable stress in the steel cable AC is 170 MPa, what should be size (diameter, in mm) of the cable to sufficiently withstand the force it is subjected to?
A solid shaft with diameter D mm and L mm long is supported between two bearings at the ends as shown in Figure 2. The shaft is to transmit a torque of T Nm and a stationary vertical load of P kN is acting at the centre of the beam. Take gY=380 MPa. 1. Find the Bending stress and shear stress due to stress-induced; 2. Evaluate the principal stress acting at the centre of the beam; 3. Determine the factor of safety for the Principal stresses obtained based on Tresca theory; 4. Determine the factor of safety for the principal stresses obtained based on Von Mises - Henky theory. P( KN) T (Nm) L (mm) D( mm) #N/A #N/A #N/A #N/A P T L mm Figure 2
A massless beam supports a dis- tributed load as shown. Determine the equivalent con- centrated load and the reactions at the x = -5 m supports. F = 3.0 N/m x = -5 m x = 0 m F = 36.0 N/m x = 5 m x = 5 m
The frame given in the figure below has three degrees of freedom in C (1,2,3) and three degrees of freedom in B (4,5,6) .In Figure 1:Open the vertical deformation at node C and apply force F and close the other degrees of freedom.Now , If we separate the CD column and the BC beamAccording to the stiffness method, what is the share of R reactions in each? why ? In Figure 2:Open the rotation at node C and insert the momentM and close the other degrees of freedom.Now , If we separate the CD column and the BC beamAccording to the stiffness method, what is the share of R reactions in each?why ?
Question One A rigid beam is supported by one rigid pin support at A and two elastic supports B and C. The length (L) and modulus of elasticity (E) of the two supports at B and C are equal. However, the bearing cross sectional area at support C is twice as it is at B (i.e. Ac=2 Ag). Calculate the reactions at the supports B and C. ... %3D 10 kN/m Im 2 m
Figure Q3 (a) shows a cantilevered beam ABC carrying a pure moment of M kN.m at point B. Thecross-sectional area of the beam is shown in Figure Q3 (b). The yield stress of the material is 250 MPa and the material is assumed to behave linearly elastic-perfectly plastic.a) Where is the critical location for the beam and give ONLY ONE (1) reasonb) Determine the moment to initiate yielding in the cross-section of the beamc) Find the value of M that can cause plastic collapse (fully plastic) in the cross-section of the beamat the critical location and sketch the variation of stressd) If the TOTAL DEPTH of the plastic zone to be 20 mm at the critical location, WITHOUT ANYCALCULATION, sketch the variation of stress.
For the beam shown below, F = 50 kN and L= 10 m. a) Determine the reactions at the supports A, B and C assuming El is constant. Consider bending strain energy only. b) Determine the deformed shape, shear force, and bending moment diagrams of the beam. F B tim TIM 2L L D L
Vertical rod CD of length L= 2 m, cross-sectional area A = 150 mm2 and modulus of elasticity E = 70 GPa supports a rigid beam AC of negligible weight, which, in turn, supports a uniformly distributed load over segment AB. When there is no load, the beam is horizontal. Determine wo (in kN/m) if the allowable stress in rod CD is 100 MPa. 2 m B. Wo A 2m
Current Attempt in Progress The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.3 in., d = 4.5 in., and t = 0.30 in. The internal bending moment about the z centroidal axis is M2 = -4.20 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. | (ур.) d a a Answers: (а) Оmax T psi (b) Omax C = psi
A wire of 2 mm diameter is wound round a circular shaft of 1 m diameter. What are the maximum normal and shear stresses in the wire? Specify the planes of their occurence. E = 1 x 10 N/mm², Assume no applied tensile pull on the wire.
Determine shear stress at support on cantilever beam as shown in figure. b = 300mm. 500mm mm 120kN/m -2.7m- 200mm
The pipe shown has an innder diameter of 60 mm and an outer diameter of 75 mm. 80-N forces are applied as shown to develop a torque. The pipe AB is 1200 mm, and the material is steel with modulus E = 30 Msi. Problem: Determine the maximum shear stress developed in the material in the outer and inner walls along the central portion of the hollow pipe. How much angular rotation is exerted by the torque?