The product structure diagram shows the number of different components required at each level to produce one unit of the final product P. If there are 50 units of on hand inventory of component A, the number of additional units of component A needed to produce 10 units of product P is (in integer). P (1) A (4) C (1) B (2) D (3) A (2) Level 0 Level 1 Level 2 Level 3

The product structure diagram shows the number of different components required at each level to produce one unit of the final product P. If there are 50 units of on hand inventory of component A, the number of additional units of component A needed to produce 10 units of product P is (in integer). P (1) A (4) C (1) B (2) D (3) A (2) Level 0 Level 1 Level 2 Level 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need an answer in half an hour
Consider 1.2 kg of a 99.6 wt% Fe-0.4 wt% C alloy that is cooled to a temperature just below the eutectoid. The iron-iron carbide phase diagram is shown in the Animated Figure 9.24. (a) How many kilograms of proeutectoid ferrite form? i kg (b) How many kilograms of eutectoid ferrite form? i kg (c) How many kilograms of cementite form? i kg
Question 3 0.4 m . . . X 0.6 m 0.6 m A B 450 N y 0.6 m Identify the directions along which the support at A prevents rotation. [Select] Identify the directions along which the support at B prevents translation. [Select] Identify the directions along which the support at B prevents rotation. [Select]
two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m
Calculate the overall order of a reaction which has the rate expression (a) Rate = k [A]\/² [B]³/2 (b) Rate = k [A]³/² [B]¯! %D
The coal combustion in the furnace of steam power plant produces 31.52 mega-Watts (MW) of heating power to produce steam. [0.1*p] mega-Watts are lost from the factory infrastructure (pipes, vanes, etc). The depleted steam is cooled by a water cooling system that expels [0.45*p] of waste heat to the environment. Calculate the net mechanical power output. Present your answer in mega-Watts (MW).
For the given beam: (a) Which of the following is the vertical reaction at c. [ Select] (b) Which of the following is the vertical reaction at D. [Select ] (c) Which of the following is the vertical reaction at B. [ Select] (d) Which of the following is the vertical reaction at A. [ Select ] | 60 kn 190 kn 400 kn 10 m 4 m By 4 m 10 m 4 m 10 m > >
Variation of the surface temperature of a pin fin is shown in the Figure. According to the figure, the following statements are made. 1-Fin is insulated perfectly. 2-The fin is in an environment with a temperature of 80 °C. 3-The efficiency of the fin is 1. 4-The heat conduction at the base of the fin is not higher than that of the tip. 5-The heat conduction at the middle of the pin is zero. Choose the correct option. 80°C 80 80 80 80°C O a. 3, 4 and 5 are correct, the rest are wrong O b. 4 and 5 are wrong, the rest are true O c. All statements are correct O d. 1 and 2 are correct, the rest are wrong O e. 4 is wrong, the rest are correct
13 Physical and CMyLab & Master Chemistry Question 12 of 12 The zero order reaction A→ Products takes 63.5 minutes for the concentration of A to decrease from 0.970 M to 0.301 M. What is the value of k for this reaction? 1 4 7 +/- 1.76 x 104 M/min 2 3 5 6 8 9 0 0 M C x 10
None
Design and manufacture of plastic and composite parts The tank shown in Figure 1 is stacked as follows: Couches individuelles: verre = glass 1 - Unidirectionnel verre/epoxy, V₁ = 62%, h = 0.010 po. 2- Mat verre/epoxy, V₁ = 40%, h = 0.040 po. Extérieur 4 Empilement: [0/35/-35/90] 3 2 3 1 Intérieur Unidirectionnel kevlar-epoxy, V₁ = 55%, h = 0.010 po. 4- Tissus 50/50, Kevlar/epoxy, 230 g/m2, V₁ = 50% h = épaisseur du PLI V₁ = Pourcentage volumique de fibres As well as the following load and dimensions: P = 3 MPa r = 50 mm L = 625 mm h = 600 mm F = 500 N N h р B x F Figure 1. multilayer composite pipe under pressure (p), also subject to torsional moment and bending moment due to force F and lever arms h and L. page 1
100 atm 1 atm 0.118 atm 114 °C 184 °C 535 °C Temperature (not to scale) a.) Use the above generic phase diagram, clearly identify where you would find the following: Gas, Liquid, Solid, Triple Point, Draw arrows and label to indicate the six transitions (melting, freezing, sublimation, deposition, vaporization and condensation) b.) Based on the above phase diagram, what phase would you be in at a pressure of 50 atm and 300°C? c.) Based on the above phase diagram at what temperature in °C would vaporization occur under normal conditions? d.) If the pressure was 0.050 atm and 425°C, what phase would you be in? e.) If the pressure was 0.118 atm and temperature was 114°C, what phase(s) would you be in? f.) At approximately what temperature would the normal freezing point be in °C? g.) If the pressure was 0.105 atm and starting at a temperature of 32°C to 450°C what phase changes would occur (put in increasing temperature order). Pressure (not to scale)