The prestressed concrete girder is made from plain stone concrete and four 3/4-in. cold-form steel reinforcing rods. Determine the dead weight of the girder per foot of its length. Let B = 13 inches. Unit weight of concrete = 144 lb/ft^3. Unit weight of steel = 492 lb/ft^3. 8 in. 6 in. 20 in. 6 in. 8 in. O B 6 in. 19.

The prestressed concrete girder is made from plain stone concrete and four 3/4-in. cold-form steel reinforcing rods. Determine the dead weight of the girder per foot of its length. Let B = 13 inches. Unit weight of concrete = 144 lb/ft^3. Unit weight of steel = 492 lb/ft^3. 8 in. 6 in. 20 in. 6 in. 8 in. O B 6 in. 19.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

600 150 150 Refer to the figure shown. Given are the following: Unit weight of concrete = 24 kN/m fe' = 35 MPa fse = 820 MPa fpu - 1,350 MPa Aps = 1,200 mm? foy = 1.080 MPa Beam is a simple span and have a length = 30 m. Determine the design moment capacity of the section. (kN-m) 00L
A reinforced concrete beam having a width of 300mm and a overall depth of 600 mm is reinforced with 2-25mm compression bars placed 60 mm from extreme concrete & 6-25mm tension bars with concrete covering of 60 mm from the centroid of the bar group. Concrete Strength, fc' = 27 MPa, Steel Strength, fy = 415 MPa. A. Determine the balanced steel area considering the contribution of the compression steel. B. Determine the maximum tension steel area allowed by the code.
The joist AB used in housing construction is to be made from 8-in. by 1.5-in. Southern-pine boards. The design loading on each board is placed as shown in the figure below. The allowable bending stress for the wood is Jallow 1.5 and the allowable shear stress is Tallow = 180 psi. Assume that the beam is simply supported from the walls at A and B. (Figure 1) Figure 1 ▾of 1 8 in. 150 lb L 150 lb L 150 lb L 1.5 in. Determine the largest room width I that the boards can span. Express your answer to three significant figures and include the appropriate units. L = 32.0 Submit μA ft My Answers Give Up ? Incorrect; Try Again; 3 attempts remaining
Reinforce Concrete Design Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression. Use f’c = 21 MPa, fy = 276 MPa and effective cover of 50 mm for top and bottom bars.Assume the load W to be ultimate. Neglect weight of beam.
A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The beam is simply supported on a span of unknown length. The uniform linear dead load from the slab is 18KN/m (weight of beam not included) and the uniform linear live load is 10kN/m. The effective depth of the beam is 430mm. the beam. Use area of one 25mm diameter bar = 510mm2. Using your own values of fc' = 20.1 MPa and fy = 335 MPa from the excel file, determine the safe length
The beam is loaded uniform deadload of 42 kN/m (including its own weight), and a uniform live load of 48 kN/m. Concrete strength fc' = 21 MPa and steel yield strength fy = 415 MPa, concrete cover is 65 mm from the centroid of the bars. Assume El to be constant. 320 mm 540 mm 7m 2m a. What is the uniform factored load on the beam in kN/m? b. What is the vertical reaction (factored) at B in KN? c. What is the maximum nominal moment can the beam carry if it is to be design as singly reinforced, in kN.m? d. What is the required tension steel area in mm2, at point of maximum positive moment? e. What is the required tension steel area in mm2, at point of maximum negative moment? f. Using simplified calculation, calculate the nominal shear strength provided by concrete near the fixed end, in KN? g. Using 10 mm W-stirrups with fyh = 275 MPa, what is the required stirrup spacing near the fixed end?
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 7 kN, and w = 2 kN/m. P KN cm w kN/m (not scaled) 290 mm a m bm b Ri R2
Referenced concrete n=1
If beam BEH is hinged at the columns B, E, and H, determine its degree of indeterminacy.
the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the uniformly distributed service dead load at beam DEF in kN/m Calculate the uniformly distributed service live load at beam DEF in kN/m.
please put in 3 decimal places thank you for the help
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h