The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld.

The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 9.5 mm. For a gage pressure of 0.83 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume β=32∘
What is the nearest magnitude of strength of a 6 mm fillet weld of 100 mm length made between two flats each 10 mm thick? The allowable shear stress on the weld is 110 MPa.
A scuba tank is being designed for an internal pressure of 2,650 psi with a factor of safety of 2.0 with respect to yielding. The yield stress of the steel is 69,000 psi in tension and 20,000 psi in shear. (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.) (a) If the diameter of the tank is 7.0 in., what is the minimum required wall thickness (in inches)? inches (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure (in psi)? psi
Pin diameter = 10 mm Gusset plate 15 kN Pin 50 mm Steel plate 6 mm thickness Column For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 131 psi, determine the normal stress perpendicular to the weld.
WELDED CONNECTIONS: THE BRACKET SHOWN IN THE FIGURE IS WELDED ON ONE SIDE OF A STEEL COLUMN WITH 800 mm OF 6 mm FILLET WELD. DETERMINE THE MAXIMUM SHEAR STRESS ON THE WELD.
A fillet-welded Joint of 6mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108MPa. The safe load that can be transmitted by the joint is 100mm 50mm
Regardless of the design load, the effective length of a 5/8 in. fillet weld that is subjected to stress in a longitudinal direction should not not be less than A. 2 in. B. 2 1/2 in. C. 3 in. D. 3 1/2 in.
Current Attempt in Progress A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ksi; a = 6.5x10-6/F] bolts have a diameter of 0.35 in. The polymer [E = 370 ksi; a = 37.2x 10-/°F] cylinder has an outside diameter of 6.9 in. and a wall thickness of 0.65 in. Assume a = 28 in. and b = 34 in. If the temperature of this assembly changes by AT = 130°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. (1) (2) (1) b. Answer: (a) 02 = psi. (b) €2 = (c) E1 = Save for Later Attempts: 0 of 1 used Submit Answer NWP Assessme. NWP Assessme. O ManyCam Desktop 30°C
Show solution and box final answer pls ty
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.