The pressure rise, AP, of a liquid flowing steadily through a centrifugal pump depends on pump diameter, D, angular speed of the rotor, @, volume flow rate, Q, and density, p. The table below gives data for the prototype and for a geometrically similar model pump. For conditions corresponding to dynamic similarity between the model and prototype pumps, calculate the missing values in the table. Variable Prototype Model ΔΡ 52.5 kPa 800 kg/m3 183 rad/s 0.0928 m³/min 999 kg/m3 367 rad/s D 150 mm 50 mm

The pressure rise, AP, of a liquid flowing steadily through a centrifugal pump depends on pump diameter, D, angular speed of the rotor, @, volume flow rate, Q, and density, p. The table below gives data for the prototype and for a geometrically similar model pump. For conditions corresponding to dynamic similarity between the model and prototype pumps, calculate the missing values in the table. Variable Prototype Model ΔΡ 52.5 kPa 800 kg/m3 183 rad/s 0.0928 m³/min 999 kg/m3 367 rad/s D 150 mm 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The initially closed valve in Figure IIIb.6.1 (b) suddenly opens. Find the time it takes velocity to reach 99% of its steady-state value. Assume that fluid is inviscid and L = 30 ft, ho = 7 ft, D = 1 in. [Ans.: 7.5 s]
Assume that the wall shear stress, Tw, created when a fluid flows through a pipe (see Figure a) depends on the pipe diameter, D, the flowrate, Q, the fluid density, p, and the kinematic viscosity, v. Some model tests run in a laboratory using water in a 0.2-ft-diameter pipe yield the Tw vs. Q data shown in Figure b. Perform a dimensional analysis and use model data to predict the wall shear stress in a 0.3-ft- diameter pipe through which water flows at the rate of 1.5 ft3/s. 0.7 Diameter = D 0.6 2 0.5 0.4 Model data (a) 0.3 0.2 0.1 0.5 1.5 Flowrate, Q, ft/s (b) Tw Ib/ft2 Wall shear stress, T,, Ib/ft? n * m N -
4. For the following system a. Give differential equations to model the fluid heights in each container. b. Write the state-variable equations in matrix form (there should be 2 variables). c. Suppose that qmi = 0, h1 = 4, h2 = 5, A1 = 10, and A2 = 4. Does fluid flow from container 1 to 2 or from container 2 to 1? Imi h2 A27
An airplane wing model is designed with a similarity test. the sustaining force is a function of speed, chord, density, viscosity, speed of sound and angle of attack. determine the dimensionless numbers
A student attempts at home to reproduce the experiment by Joule performed in the mid-nineteenth century. In the student's experiment, a weight takes 20 minutes to fall a distance, z, under gravity whilst pulling on a wire that turns a paddle emersed in a fluid inside an uninsulated copper container (see illustration). The temperature of the fluid is monitored by an accurate thermometer emersed in the fluid. A first temperature reading is taken just before the mass begins to fall and a second temperature reading is taken just after the mass has fallen a distance, z and come to rest. Falling mass rotates paddle. Fluid Rotating paddle Copper How many of the following statements are correct: al The work performed by the falling mass goes solely to raising the internal enerav
(b) One form of fluid movement is rotation and deform angularly. Figure Q1(b) shows the rotation and angular deformation caused by velocity variation about z-axis. Based on Table 1 and setting given to you, derive an equation of rotation. ди Sy St ây > B' ĉu B B ôy dy A' ↑ Sa v+. ôx A ôx Figure Q1(b) : Rotation and Angular Deformation Table 1: Axis of Rotation Setting Axis of Rotation 2 у-ахis
Problem 1: The discharge pressure (P) of a centrifugal pump shown below is a function of flow rate (Q), impeller diameter (D), fluid density (p), and impeller angular speed (12). P = f (Q. D, p. 92). Use the Buckingham pi technique to rewrite this function in terms of dimensionless parameters, 1 g (n₂). P= P(Q,D, Dimensions 2) N= 5 Q. P
4. A pump is required to pump fresh water at a flow rate of 5000 m³/hour against a head of 8 mat a speed of 1500 rev/min. It is planned to test a scale model with a head of 2 m at a flowrate of 100 m³/hour under dynamically similar conditions (but neglecting changes in ReynoldsNumber). Determine: a) The speed at which the model must be run.b) The scale that must be used for the model.c) The mechanical power required to drive the model pump is found to be 680W at theoperating point. Calculate the power required to drive the full scale pump.d) After the full scale pump is fitted into the system it is found that the pump head risereally needs to be increased by 30%. At what speed should the full scale pump now berun at to achieve this head rise and what will be the new ideal flow rate and powerconsumption in order to match this operating condition?e) Briefly comment on the main advantages and limitations of testing a scale model toprove the performance of a larger prototype.
26. A horizontal pipe of 150 mm diameter and 200 m length conveys water from a reservoir to a nozzle 50 mm in diameter. What would be the power of the jet if the level of water in the reservoir is 15 m above the axis of the pipe? Take friction co-efficient = 0.01. Neglect losses in the nozzle. [Ans. 2.31 kW]
Problem 5 s): The discharge pressure (P) of a screw pump (Fig. 5) is a function of flow rate (Q), screw diameter (D), fluid viscosity (u) and screw angular speed (w). P = f (Q, D, μ, w). Use the pi theorem to rewrite this function in terms of dimensionless parameters, ₁ g (T₂). Choose Q, D, and u as repeating variables. Screw Fig. 5: Screw pump
In this question, assume the "additional displacement" is in the positive u direction. A mass weighing 16 lbs stretches a spring 8 inches. The mass is in a medium that exerts a viscous resistance of 1 lbs when the mass has a velocity of 2 ft/sec. Suppose the object is displaced an additional 5 inches and released. Find an equation for the object's displacement, u(t), in feet after t seconds. u(t) =
HELPPPPPP URGENTTTTTT!!!