The pressure at entrance of the bend is 138 kPa. The combined weight of the bend and its content is 268 kN. Neglecting friction in the flow, compute the minimum volume of concrete block holding the bend that can withstand the thrust of water on the bend assuming the coefficient of friction between the concrete a

Q: IF Ho=5m,a320, B=100,pd%3D1600, 0=36 and 6=24 Calculate the safety of the gravity wall and determine…

A: Given data, Ho=5m α=20°β=100°φ=36°δ=24° we have to calculete the factor of safety against capacity…

Q: Determine the Internal Forces at  AL BL GH FG AB in Kn

A:

Q: A 1.2-m length of a steel pipe 500 kN of 200-mm outer diameter and 12-mm wall thickness is used as a…

A: Given data in question  Load Length Outer diameter  Thickness  Poissons ratio Elasticity modulus  To…

Q: Help

A:

Q: A 2.75-m-diamter wood-stave pipe has 9 m3/s of water entering through a horizontal 30o reducing bend…

A: Solution-Diameter of the wood stave piped=2.75mDischarge of water=9m3/sAngle of bending θ=30°Unit…

Q: IN PRO a) EACH BLEMS CALCULATE 95 10m V s 450 -20. 100 KN - 100 KN 10m DRAW ALL T THE 1-3-f 20m…

A: given data,bemas are given solving first threea)b)c)FINDreactions

Q: A built-up laced column of overall square cross-section, 300 mm size has been formed by placing four…

A:

Q: A vertical triangular plate has a base of 1m and depth of 2.1m. The base is horizontal and flushed…

A:

Q: A short rectangular column 500 mm on one side and 600 mm on the other side. It is reinforced with…

A: Answer  (1) Calculation of distance from Neutral axis At ultimate stage we get strain in extreme…

Q: 2. WHAT IS THE MAXIMUM Pt Ре оо O 20 dia mm BEARING STRESS : 100 MPa SHEAR STRESS : 150 MPa STRESS :…

A: Given data:Bearing stress= 100 MPaShear stress =150 MPaStress= 80 MPa

Q: 2. For the pipe flow-reducing section shown below, D₁ = 8 cm, D₂ = 5 cm, and p2 is at atmospheric…

A: Given : D1 = 8 cm and D2 = 5 cm V1 = 5 m/s h = 58 cm Determine the force resisted by the bolts ?

Q: Design the Slabs of the shown Structure.

A: To design the slab for the given specifications

Q: 36. A vertical concentric load of 1800 N is supported by a tapering concentric column. The column…

A:

Q: 175 mm 300 mm/ 300 mm, 300 mm 300 mm 300 mm, 3.6 m 300 mm,

A:

Q: FAR = 5.56 kN tension 80 kN FAE = 75.56 kN tension %3D FBC = 4.45 kN tension FBE = 3.34 kN…

A:

Q: Consider a cantilever truss with variable section (figure 7.3). Determine the forces and types of…

A: Step 1: Understanding the TrussThe truss is cantilevered with varying sections and different lengths…

Q: Determine the design moment capacity of the reinforced concrete beam shown in Figure 1(a) if it is…

A: Solution: Given: b = 300 mm d = 560 mm fy = 276 MPa fc = 21 MPa Steel in tension = 4#28 mm Steel in…

Q: In rectangular tanks: Mz gives reinforcement parallel to: Y direction XY direction Z direction O X…

A: Water storage tanks are very important public structures. They may be under ground, over ground or…

Q: Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE…

A: Hydrostatic forces on surfaces deals with the fluids i.e., liquids and gases at rest. The velocity…

Q: A damper square mat is supporting a dead load weigh 8 kN. Helical springs will be used to support…

A: According to given data

Q: 2. For the pipe flow-reducing section shown below, D₁ = 8 cm, D₂ = 5 cm, and p2 is at atmospheric…

A:

Q: Further problems 293 A vertical masonry chimney has a internal diameter d, and an external diameter…

A: The given data is as follows: Internal diameter=diExternal diameter=doHorizontal acceleration=a…

Q: AIR 4. AIR 1,5 OIL S.Gz0,9 FIND ΤΗΕ AIR VALUE OF WA TER THE RESULTANT FORCE ON WALL ABC 2 m FBD WALL…

A: unit wt of water γw=9.8 KN/m3unit wt of oil  γO=0.9×9.8=8.82 KN/m3pressure variation over the depth…

Q: Q-A rectangular column section of 250mm x 400mm is reinforced with five M30. steel bars of grade Fe…

A: Given data- Rectangular column section- 250 mm×400 mm,5 steel bars, Fe500,dia d=20 mm,M30 concrete,…

Q: 0.90m 0.25m 0.30m

A:

Q: H.W A shaft com Posed of Segments Ac,cD and DB s fastened to igid SuPPorts oand looded as shown, for…

A:

Q: . Refer to the beam shown below. Internal hinges are insta Given: kN/m

A:

Q: M, Q5. The pipe is fixed to the ground at point A. It is simultaneously subjected to normal force of…

A: The given data is: Force F=10 KN Bending moment, Mx=1 KN-m Torque, T=2 KN-m Allowable stress…

Q: A cylindrical gate 10m long and 6m diameter is as shown. Assume that the cylinder does not rotate,…

A: GIVEN: Length of gate = 10m Diameter of gate= 6m Coefficient of friction=0.2 To determine:  Weight…

Q: of the beam

A: Given data As=8-25mm bars (fy=350MPa) depth=500mm

Q: 2. For the pipe flow-reducing section shown below, D₁ = 8 cm, D₂ = 5 cm, and p2 is at atmospheric…

A: Given Data : D1 = 8 cm D2 = 5 cm V1 = 5 m/s h = 58 m To Find : Determine the force resisted by the…

Q: Determine

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?