حالة إكمال الأسئلةThe power output of an adiabatic steam turbine is 4.5 MW, and the inlet and outlet conditions of the steam are given below. Perform the following calculationsa) Calculate Ah, Ake, Ape (in kJ/kg) and the mass flow rate of the steam in kg/sOutlet parametersInlet parametersP2 = 10 kPaP1 = 2.5 MPaT1 = 450 °CV1 = 53 m/sX2 = 83%V2 = 183 m/sz2 = 4.5 m21 = 8.5 mg = 9.81 m/s2Steam* 44F5F1PrtScF104t334.017V.89.%DYUP :ASGYH1.L.13CVBYNIMAlt3eAlfCrl11V nJUDI P2V272Ah = -1142.9, Ake = 15.21, Ape = -0.039 (all units are in kJ/kg)%3Dmass flow rate = 3.55 kg/sAh = -1174.4, Ake = 15.34, Ape = -0.039 (all units are in kJ/kg)mass flow rate = 3.88 kg/sAh = -1095.9, Ake = 15.47, Ape = -0.039 (all units are in kJ/kg)mass flow rate = 4.63 kg/sAh = -1017.3, Ake = 15.6, Ape = -0.039 (all units are in kJ/kg)mass flow rate = 5.49 kg/s

Answered: Image /qna-images/answer/8a368cf8-8cca-41d1-a371-96af8d900bc7.jpg

The power output of an adiabatic steam turbine is 4.5 MW, and the inlet and outlet conditions of the steam are given below. Perform the following calculations a) Calculate Ah, Ake, Ape (in kJ/kg) and the mass flow rate of the steam in kg/s Outlet parameters Inlet parameters P2 = 10 kPa P1 = 2.5 MPa X2 = 83% T1= 450 °C V1 = 53 m/s V2 = 183 m/s 22 = 4.5 m 21 = 8.5 m g = 9.81 m/s2 T Steam

The power output of an adiabatic steam turbine is 4.5 MW, and the inlet and outlet conditions of the steam are given below. Perform the following calculations a) Calculate Ah, Ake, Ape (in kJ/kg) and the mass flow rate of the steam in kg/s Outlet parameters Inlet parameters P2 = 10 kPa P1 = 2.5 MPa X2 = 83% T1= 450 °C V1 = 53 m/s V2 = 183 m/s 22 = 4.5 m 21 = 8.5 m g = 9.81 m/s2 T Steam

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inlet temperature of an air compressor is T₁=300°K and the outlet temperature is T2-500°K. The compressor operates at a mass flow rate of 0.093kg/sec and the heat lost during the compression is 10kJ/kg. Assume that the air is an ideal gas with Cp=1.004 kJ/(kg°K). Calculate the mechanical power needed to be provided to the compressor shaft. Present your answer in kilo- Watts (kJ/sec).
Time left 0:22:28 Air enters a compressor with h₁ = 378.7 kJ/kg and exists with h₂ = 7134 k/kg Steam enters a turbine with the shown conditions and exis's the turbine with quality x= 15%. If 13.4% of the turbine power is used to drive the compressor and the rest of the turbine power is sed to drive an electrical generator that needs 1.35 MW, what is the mass flow rate of the air (kg/s)? Note: Enter your answer. 1 MPa 10.0MP 700°C Answer: > < Air compressor ON L.P
Fluid Mechanics
A fluid undergoes a frictionless process in a closed system form v1=5ft to v2=2ft^3 in accordance with the relation v=36/(p-8) where p is the psia and v is ft^3. During the process, the fluid rejects 30 BTU/lbm. Compute the change of heat transfer.
Water enters a 5-L tank at a rate of 4.00 kg/s and is withdrawn from the tank at a rate of 6.00 kg/s. The tank is initially four-fifths full. (a) Write a mass balance for this process by assigning a variable function to the mass of water at time t. Describe the terms that are present in the balance; give reasons for deletion of any terms. (b) Solve the balance to find how long it will take the tank to drain completely.
Q4/ A rigid tank contains hot fluid that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 800 kJ. During the cooling process, the fluid loses 500 kJ of heat, and the paddle wheel does 100 kJ of work on the fluid. Determine the final internal energy of the fluid. Neglect the energy stored in the paddle wheel. Qout=500 kJ U₁ = 800 kJ U₂ = ? Fluid Figure (2) Wsh.in = 100 kJ
Problem A steam turbine operates with 1,6 MPa and 350 deg C steam at its inlet and saturated vapor at 30 deg C at its exit. The mass flow rate of the steam is 22 kg/s, and 610.2 kW of heat is lost through the casing of the turbine. 1. Create a sketch of the problem and indicate the control volume. 2. Write the continuity and energy equations and cross out terms by stating the relevant steady state assumptions. 3. Determine power produced. 4. Determine the specific work.
solve the following question and show the complete solutions
THERMODYNAMICS TOPIC: FIRST LAW OF THERMO/THERMODYNAMIC SYSTEM PLEASE ANSWER COMPLETELY THE QUESTION IN HANDWRITING AND SUPPORT YOUR SOLUTION WITH DIAGRAMS. THANK YOU