The position of a particle in millimeters is given by s=54-15t+t2 where t is in seconds. Plot the s-t and v-t relationships for the first 9 seconds. Determine the net displacement As during that interval and the total distance D traveled. By inspection of the s-t relationship, what conclusion can you reach regarding the acceleration? Answers: As= -54 D= i 80.75 mm mm

Q: ((2+ dy : 2 3 2 3 8/y - 4y +y² + C 8,/5 - 4y -y + c 2 3 8/y + 4y -yž + c 2 3 8/y + 4y + yž +C

A:

Q: Find the Shear Moment Diagram of the following problems using

A:

Q: The value of the spring index for a helical spring is 10. Calculate the outer diameter of the spring…

A: Given Data  C=10 D=53 mm

Q: I made a custom made shaft using solidworks. and it's designed with a custom made steam turbine…

A: Filet is an inside or outer round highlight at the side of a section. Outside filets are raised, and…

Q: An experiment on the life of a cutting tool at different cutting speeds are given bellow Speed v…

A: Given: To find: To find a relation between v and T  where v is cutting speed T is tool life

Q: I have a hole shaft interface with the following dimensions hole .500/.504, shaft .494/.499 which of…

A: Solution:

Q: 4. Ø.009MAB@ Answer:

A: refer generalized representation of geometric tolerance.

Q: 6-1 The operating point of the zwo components are nes per Duct: m- Fan: where SP = static pressure,…

A:

Q: The external torque on a drill bit varies linearly to a maximum intensity q, in.Ib/in . If the drill…

A:

Q: A V-belt pulley is made of cast iron with 240 mm. in diameter is connected to a 360 mm. diameter…

A: To Find :The Arc of lengthGiven :The Diameter is The Center distance is,

Q: 22 R 50 -38 24 10 125 41 20 Drill 48 27 -20.5 -

A:

Q: Algebraic reduction S=27C$ for small attenuation. Show that s has the following relationship with…

A:

Q: Find the ratio of E/K if poisson ratio is 0.272

A:

Q: 3k 2k a) Determine DoF b) Obtain governing equations.( hari tntal plane)

A: a) As we can see from the figure that there are two masses which are not connected by a rigid link.…

Q: A chain with a 0.75 in pitch is designed to run on sprockets having 15 and 50 teeth, respectively.…

A: Given data: n=15N=50p=0.75 inCD=36 in Need to determine the length of chain required in pitches.

Q: In Fig. 8.32 two tunnels AB and EF are being driven forward until they meet in order to accommodate…

A:

Q: The loading at point A, w₁ = a +bx+cx₁² 1=a+b(0.4) + c(0.4)² .....(1) The loading at point B, W₁ = a…

A: Find the value of constant in three equations. Solving using matrix.

Q: Determine homogeneous equation by applying Leibnitz Mclaurin method xy"+y'+2xy=1 show all working

A: xu′′v+u′v(2x+1)+uv(3x)+xuv′′=0This is the homogeneous equation obtained by applying the…

Q: a. Solve for R() as a piecewise function of x b. Solve for o(x) c. Solve for ɛ(x) d. Solve for u(x)

A:

Q: 1. Fill in the blanks according to the given information Hole Shaft 040. 009 -0. 025 +0. 021 040*0.…

A: Nominal size: It is the ideal size of part which is required to design. upper limit of size: It is…

Q: a=75 mm b=160 mm c=20 mm determine the moment of interia Y prime

A: Given Data

Q: S. Fig Q5 shows a shaft of gearbox rotating about x axis. Shafi BC is a solid shalt with dircular…

A:

Q: Q.4. The approximated time of a ball to reach at ground when dropped from a 4 n is 3 seconds. But…

A: Given Data : True Time(Experimented value)=2.1 s Approximated time=3 s

Q: The common equation used to calculate the transverse shear stress in a member is: Terans" Starting…

A: Show that,

Q: Assuming there is no axial thrust, find the reactions @ A ± C. Y Note: Force actlig on gear B is…

A: There is no axial forceAt gear B force is parallel to z axis At gear D force is parallel to y axis

Q: 7. A shaft with a length of 5 m is subjected to a twisting moment of T=4x10 N.mm. If J=620x10 mm,…

A:

Q: The turning moment diagram of a quadruple expansion marine engine (multi cylinder engine) drawn to…

A:

Q: A shaft shown in figure is acted upon by a radial force F=50N. If the shaft is made of steel,…

A: Given: F=50 N To find: Critical speed=?

Q: A torsion dynamometer is fitted on a turbine shaft to measure the angle of twist. It is observed…

A: The solution is mentioned in next step

Q: Derive the torsion formula.

A: The Answer is below.

Q: L. L. 2d (1) 4d 2d + 27 3d D. 2d H. 37 (3) 21 The shaft system shown above is made up of shaft…

A:

Q: The endpoints of a movable rod of length 1 meter have coordinates (x, 0) and (0, y) (see figure).…

A:

Q: The linear displacement is also a product of average velocity and time.  Select one: True False

A:

Q: • Determine the displacement and rotation at B El is constant A W a b B

A: Given data:- To find:-the displacement and rotation at B

Q: 4. A Cantilever beam deflects downwards when a mass is attached to its free end. The deflection(6)…

A: solving the no. 4      Here we have Note that the slope of the straight line with value of 'Mg'…

Q: As shown, a shaft is composed of five cylindrical sections. A motor is attached at F and supplies…

A:

Q: Calculate the Virtual Condition of the PIN in the drawing below: 1.000 C 2.000 Ø.995-1.000…

A: Draw the given drawing.

Q: pplied to end of torque arm = of torque moment arm = 150

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.