HW9.1 The velocity distribution for laminar flow between parallel plates is given by - (²3) ² u y Umax h where h is the distance separating the plates and the origin is placed midway between the plates. Consider a flow at 15°C, with Umax=0.80 m/s and h = 0.10 cm. Calculate the shear stress on the upper plate and given its direction. Sketch the variation of shear stress across the channel. Hint: for water at 15°C, μ = 1.1 x 10-3 N.s/m²

HW9.1 The velocity distribution for laminar flow between parallel plates is given by - (²3) ² u y Umax h where h is the distance separating the plates and the origin is placed midway between the plates. Consider a flow at 15°C, with Umax=0.80 m/s and h = 0.10 cm. Calculate the shear stress on the upper plate and given its direction. Sketch the variation of shear stress across the channel. Hint: for water at 15°C, μ = 1.1 x 10-3 N.s/m²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water falls down a vertical pipe by gravity alone. The flow between vertical locations z1 and z2 is fully developed, and velocity profiles at these two locations are sketched. Since there is no forced pressure gradient, pressure P is constant everywhere in the flow (P = Patm). Calculate the modified pressure at locations z1 and z2. Sketch profiles of modified pressure at locations z1 and z2. Discuss.
A circular pipe flow, the diameter d=50mm, mean velocity of water flow in the pipe v=1.5m/s, kinematic viscosity v = 0.89x10m/s when water temperature is 25°C. Judge flow regime in the pipe.
Look around and identify some internal fluid flow through a long “pipe" section. Estimate Reynold's number for that flow. State all values used to calculate Re and the methods used to find/estimate the values-rough estimates are not only okay but expected. Conclude by stating if you expect (or observe) the flow to be turbulent or laminar.
Q.6 The velocity profile in fully developed laminar flow in a pipe of diameter Dis given by u=u (1-4r2/D²), whereris the radial distance from the center. If the viscosity of the fluid is u, the pressure drop across a length L of the pipe is %3D
60m 44m (2) (1) (3) 40m (4) 40m (5) 42m c) Find the flow discharge within the system. (6) 30m 35m Q (2). You have a tank open at the top, flow in the 25-cm-smooth-65 m long- plastic pipe. (7)
(2) It is desired to deliver 60 m'/hr of water at 20°C through horizontal asphalted cast iron pipe. Estimate the pipe diameter d that will cause the pressure drop to be exactly 40 kPa per 100 m of pipe length. Take water density p Solve this problem iteratively using either Moody chart or the Colebrook equation. 998 kg/m and dynamic viscosity µ = 0.001 kg/(m.s).
A two-dimensional reducing bend has a linear velocity profile at section (1). The flow is uniform at sections (2) and (3). The depth of the bend perpendicular to the plane of the paper is 1 ft. Consider steady incompressible flow. Calculate the discharge at section (1). Also calculate the magnitude and h₁ = 2 ft direction of the uniform velocity at section (3). Hint: the cross-sectional areas are rectangular VA V₁, max 10 ft/s h3 = 1.5 ft- V2 = 15 ft/s - h₂ = 1 ft 0 = 60°
Water ( density 1000kg/m3) flows downward naturally through a vertical pipeline of diameter D=25 cm and length L= 100 m . Determine the pressure gradient causing flow ( USE π = 3 ; g = 10 m2/s ) ANSWER: 10 kPa/m (Although I wrote this is the answer under the question in some of the questions I posted before. Different answers were found from the answer. The exact answer to this question is 10kPa / m.)
A ship 50 m long, with a wetted area of 800 m2, has the hullshape tested in Fig. There are no bow or stern bulbs.The total propulsive power available is 1 MW. For seawaterat 20°C, plot the ship’s velocity V kn versus power Pfor 0 < P <1 MW. What is the most efficient setting?
Show work for both subparts as it is a single problem.
What is the total force acting on a 90 degrees pipe bend if the flow pressure is 3 x105 Pa, the flowrate is 0.1m3/s and the specific gravity of the fluid is 0.7. The pipe diameter is 10cm and the weight of the fluid can be neglected (remember to consider both force components).
Please solve