The piston with frictionless cylinder as shown contains 1kg steam at 200kPa and 500°C. The setup is cooled and at 250°C the piston touches the spring. The setup is cooled further to a temperature of 150°C and a volume of 1.1m³ Calculate the work [A1] and heat transfer [A2] in kJ Assume a linear spring. Win = 116.5+ 19.0 = 135.5kJ Quit cont = 688.6kl

The piston with frictionless cylinder as shown contains 1kg steam at 200kPa and 500°C. The setup is cooled and at 250°C the piston touches the spring. The setup is cooled further to a temperature of 150°C and a volume of 1.1m³ Calculate the work [A1] and heat transfer [A2] in kJ Assume a linear spring. Win = 116.5+ 19.0 = 135.5kJ Quit cont = 688.6kl

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Completely solve. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. BOX THE FINAL ANSWERS. At 51 lb/in2, a mass of 0.22 lbm of helium fills a 7.1 ft3 rigid vessel. The pressure in the vessel is heated until it reaches 101.53 lb/in2. Calculate the final temperature for helium. R= 2077.67 kJ/kg-K, Cp = 5.2028 kJ/kg-K, Cv= 3.1233 kJ/kg-K.
10. From Newton's law of cooling, the boiled egg submersed in water in the diagram below will cool according to dI = -0. 1(T – a), T(0) = 100°C . Solve this differential equation and express T in terms of a. Do not use the integrating factor method. Present your solution with T as the subject. Use your solution to solve the following: If after 1 = 10 time units this egg cools to T = 2ª°C , what was the value of a (a is the temperature of the water in the glass which is assumed to have remained constant)?
how to solve this thermofluid?
(2) A 30° MK = 0.45 Мк G B MA= 1 = 2 ку .8 kg - In the above arrangement of two blocks and card, the blocks start Use PWE to at rest, and the pulleys are frictionless. Find VA (mag and direc) after may assume that the card tension You B has descended by 0.65 m. is constant. You will need to use NSL to relate N₁ to WA E=mAg), NA and you Should show all the steps of this preliminary step also.
Q4/ A rigid tank contains hot fluid that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 800 kJ. During the cooling process, the fluid loses 500 kJ of heat, and the paddle wheel does 100 kJ of work on the fluid. Determine the final internal energy of the fluid. Neglect the energy stored in the paddle wheel. Qout=500 kJ U₁ = 800 kJ U₂ = ? Fluid Figure (2) Wsh.in = 100 kJ
dsphere dbar • Given the above system, two spheres attached to the ends of a cylinder, determine the mass moment of inertia about the axis normal to the page as a function of the variables provided. Note, you can treat the masses of each element of the system as known o (msphere and mbar). After deriving an expression for the mass moment of inertia about the axis normal to the page as a function of the variables, calculate the mass moment of inertia given: osphere properties ▪ mass of sphere = 5 kg 1 diameter of sphere = 0.5 m bar properties ▪ • Determine the resultant force and moment acting on the system if the system is moving as follows: mass of bar = 25 kg length of bar = 7.5 m diameter of bar = 0.25 m O a = 5î+ 2ĵ m/s² O αG = 7k rad/s² ασ
3-4: Inlet steam at 17.5 MPa and 600 ˚C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the specific entropy in kJ/kg at state 4 to 3 decimal places.
THERMODYNAMICS TOPIC: FIRST LAW OF THERMO/THERMODYNAMIC SYSTEM PLEASE ANSWER COMPLETELY THE QUESTION IN HANDWRITING AND SUPPORT YOUR SOLUTION WITH DIAGRAMS. THANK YOU
Initial condition: P = 0.7 MPax = 96 %Process: ThrottlingFinal condition: P = 0.35 MPaRequired: Δs
pls answer soon S= 0 T= 1 U = 8