The pin-connected structure consists of two cold-rolled steel [E = 28,000 ksi] bars (1) and a bronze [E = 14,000 ksi] bar (2) that are connected at pin D. Each steel bar has a cross-sectional area of 0.375 in.?. A load of P = 18 kips is applied to the structure at pin D. Using a = 3.2 ft and b = 6.3 ft, calculate the area required for bar (2) so that each bar carries the same force. a B (2) (1) (1) b D Answer: A2 = i in.?

The pin-connected structure consists of two cold-rolled steel [E = 28,000 ksi] bars (1) and a bronze [E = 14,000 ksi] bar (2) that are connected at pin D. Each steel bar has a cross-sectional area of 0.375 in.?. A load of P = 18 kips is applied to the structure at pin D. Using a = 3.2 ft and b = 6.3 ft, calculate the area required for bar (2) so that each bar carries the same force. a B (2) (1) (1) b D Answer: A2 = i in.?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN