The picture shows two perpendicular wires where I1 is 14.6 amps, and I2 is 21.9 amps. The location A is in the plane of the two wires and is 25.0 mm from the x-axis and 15.9 mm from the y-axis. Given the direction of current in each wire, what is the B-field at the location A in micro teslas? (If the B-field points toward you, make it positive; if it points away from you, make it negative. Give answer as an integer with correct sign. Do not enter unit.)

The picture shows two perpendicular wires where I1 is 14.6 amps, and I2 is 21.9 amps. The location A is in the plane of the two wires and is 25.0 mm from the x-axis and 15.9 mm from the y-axis. Given the direction of current in each wire, what is the B-field at the location A in micro teslas? (If the B-field points toward you, make it positive; if it points away from you, make it negative. Give answer as an integer with correct sign. Do not enter unit.)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Two wires are located at the distance d=4m as shown in the diagram. y d/2 #1 #2 d/2 A d/2 d/2 B Wire #1 carries a current of 4 A in the shown direction. Wire #2 carries a current of 2 A in the shown direction. Hol Units: Tesla (T) B = 2nr' Ho=47tx10-7 T*m/A 1. Find the magnitude and direction of total magnetic field at point A, located exactly in the middle between two wires. 2. Find the magnitude and direction of total magnetic field at point B, located at the distance d/2 to the right of wire #2 as shown in diagram. 3. Find the magnitude of total magnetic field at point C, located at the distance d/2 above the point A as shown in diagram. 4. Find the direction (angle related to positive +x axis) of total magnetic field at point C, located at the distance d/2 above the point A as shown in diagram.
A wire with a resistance of 1.2 ΩΩ is bent into the two-loop shape shown in (Figure 1). The length of the sides of the large square is 9.0 cmcm; those of the smaller square are half that, If the magnetic field shown is increasing at a rate of 0.075 T/sT/s, what is the current in the wire?
A resistor R is connected between two parallel conducting rails separated by 30 cm, as shown in the diagram. A conducting bar maintains electric contact with the rails as it moves relative to them with constant velocity from x = 20 cm to x = 48 cm in 0.6 seconds. A uniform 0.8 T field points into the page. Calculate the induced electric potential difference between the two ends of the bar.
A circuit is made with a resistor of resistance 25 ohms and a movable bar with length 15 cm moving to the left with speed 8 m/s. The whole circuit is in a magnetic field B = 1.5 T (into page). Use this set up to answer the following questions. What is the magnetic force on the bar in Newtons? Answer to 4 decimal places.
When the current flows clockwise on a 2D diagram of a circuit, what is the direction of the magnetic field, clockwise, counter-clockwise, into the page, or out of the page?
A rectangular slab (length 2.5 cm, width 1.5 cm, thickness 5.0 mm) of an unknown semiconductor with an unknown dopant was analyzed by placing it under a perpendicular magnetic field of strength 0.10 T in the +y direction, as well as subjecting it to a current of 7.5 A in the +x direction. A voltmeter measured that the potential on the top of the slab (as seen from the front) is 93.75 mV higher than the bottom. What is the majority charge carrier?Justify why.
This is not an essay question, im trying to figure out how to solve for the solutions.
A set of wires arranged on the corners of a square of side length ?s each carry a different current, as shown in the figure. The wire in the lower left corner carries a constant current ? in the k-direction. The wire in the upper left corner carries a current I→1=−I⁢k, the wire in the upper right corner carries a current I→2=−12⁢I⁢k, and the lower right wire carries a current I→3=I2⁢k. Determine the vector expression for the net magnetic force FB→ per unit length L on the lower left wire using ??? unit vector notation. Express your answer in terms of the permeability μ0 of free space, s, ?, and numerical constants.
The capacitor in the circuit shown below is initially uncharged. The switch is closed at t = 0 s. AV battery = 30 V, C = 3.0 F, and R = 2.0 2. At sometime after the switch is closed, the current in the circuit is measured to be 9.3 A. What is the charge on the capacitor at this time, in Coulomb? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.
A current I = 3 A is passed through a wire. A second wire of length L = 1 m is moving with velocity v= 285.4 m s¨¹ at a distance d=1 cm perpendicular to the magnetic field generated by the first wire (see sketch below). Calculate the current in the circuit that includes the second wire and a stationary piece of wire (green in the sketch below). Take the resistance in the circuit to be 10 Q2 (Ohm). Consider the magnetic field B to be constant over the range of motion of the second wire (i.e. d » 1 ). For the permeability of vacuum take μo = 1.3×10-6 NA². Provide your answer in milliamperes (mA). Enter your answer in the box below. Wire 1 Wire 2 اد Wire loop
An aluminum bar moves with a speed 2m/s between two copper roads in a magnetic field of 2T as indicated on the figure. The distance between the cooper roads is 10m. The aluminum bar is always in contact with cooper roads and moves without friction. A voltmeter is coupled between the roads. What is the potential measured by the voltmeter (in volt), if the resistance of the rods and aluminum bar are consider to be negligible?
Draw a sketch of the situation in the figure, showing the direction of electrons carrying the current, and use RHR-1 to verify the direction of the force on the wire.