The partition coefficient for compound A between hexanes and water is 12. Assume 10 g of A is dissolved in 100 mL of water. This aqueous solution is extracted with 30 mL of hexanes, for a total of four extractions, how much of A can be extracted? State your answer in terms of grams. Do not include units in your answer. Use three significant figures in your answer.

The partition coefficient for compound A between hexanes and water is 12. Assume 10 g of A is dissolved in 100 mL of water. This aqueous solution is extracted with 30 mL of hexanes, for a total of four extractions, how much of A can be extracted? State your answer in terms of grams. Do not include units in your answer. Use three significant figures in your answer.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Dimethylformamide (often abbreviated as DMF, see structure below) is a very common high boiling solvent used in organic synthesis. With which of the following solvents is DMF most miscible (soluble)? 'N' "DMF" H3C-CEN "acetonitrile" "cyclohexane" "hexane" "m-xylene"
3 Draw a flow chart to shows the strategy for separation of three compounds: Phenanthrene and 4-Aminoacetophenone and 1,4-Dibromobenzen and dissolve mixture is Diethyl ether. add NaOH (1M) and (6M) to the aqueous layer and ether layer..
Propose an extraction flowchart capable of separating this compound into its pure form
Briefly explain how you determined when the reaction was complete PROCEDURETo a six inch test tube was added thiamine hydrochloride (0.65 g), followed by water (2mL). The mixture was gently shaken until homogeneous, and then ethanol (7.5 mL)was added. Finally, sodium hydroxide (10%, 1.5 mL) was added and the mixture wasgently stirred to ensure complete mixing.Benzaldehyde (3.8 mL) was then added at room temperature in one portion with gentlestirring. The pH of the resulting reaction mixture was determined and adjusted to >10by dropwise addition of 10% sodium hydroxide. The reaction mixture was then partiallysubmerged in a 65 °C water bath2 and the progress of the reaction was periodicallymonitored by TLC analysis.Once TLC analysis indicated that the reaction was complete, the reaction mixture wascooled to approximately room temperature, and then chilled in an ice-water bath. Theresulting precipitate was collected by vacuum filtration and air-dried. The crude productwas purified by…
What is the experimental yield (grams and percentage) Experiment: Oxidation of -Chlorotoluene to o-Chlorobenzoic acid materials used dissolved 3.35 g of KMnO4 1.20 mL of 2-chlorotoluene was added to the mixture 3.0 mL of concentrated hydrochloric acid (pH~2) 10 mL of toluene -The crystals were isolated by vacuum filtration- Product Characterization 1.15 g of the crude product 0.93 g of the final product M.p. (final): 139-141 oC
C)
Which of the following is expected to achieve the best recovery of an organic compound from an aqueous solution? 1.Three extractions with 20 mL of ethyl acetate per extraction (60 mL total) 2.Two extractions with 30 mL of ethyl acetate per extraction (60 mL total). 3.One extraction with 60 mL of ethyl acetate. 4.In theory these extractions yield identical recoveries of the organic compound.
In which of the following cases would recrystallization be favored over extraction when purifying a mixture of two solid compounds? I. When a significant difference in pKa exists between the two compounds. II. When both compounds have the same functional group(s). III. When the desired compound is poorly soluble in the solvent pair at low temperatures and greatly soluble in the solvent pair at high temperatures. A. I and III B. II C. II and III D. I and II E. I, II, and III F. None of the above
Melting point range Recrystallized Phenacetin 95-100 Recrystallized Phenacetin + Reference Phenacetin 110-115 Recrystallized Benzil 92-95 Recrystallized Benzil + Reference Benzil 94-98 Questions: 1. What does your melting point say about the purity of your phenacetin sample? Justify your answer using the characteristics of mixed melting point. 2. What does your melting point say about the purity of your phenacetin sample? Justify your answer using the characteristics of melting point. 3. What are two characteristics of a good recrystallization solvent for a given compound? 4. Given a solid sample that contains impurities, how would you determine which solvent to use for a recrystallization? Describe how you would do this in the laboratory. 5. Clearly explain the difference between a recrystallization and a precipitation.
Synthesis of Aspirin and Oil of Wintergreen Explain what will happen to the (i) yield and (ii) purity, of aspirin if the following steps were modified in its synthesis Yield then explanation