The oxidation of o-dianisidine (o-DIA) is electrochemically reversible and involves the transfer of two electrons. Linear sweep voltammetry was performed on a 2 M H, SO, solution containing 2.32 mM of o-DIA using a carbon paste electrode with an area of 2.56 mm². At a scan rate of 500.0 mV/s the peak current was 5.61 µA. Determine the diffusion coefficient, D, for o-DIA. D = cm2/s Determine the peak current if the scan rate is reduced to 350.0 mV/s. Ipe = HA %3D

The oxidation of o-dianisidine (o-DIA) is electrochemically reversible and involves the transfer of two electrons. Linear sweep voltammetry was performed on a 2 M H, SO, solution containing 2.32 mM of o-DIA using a carbon paste electrode with an area of 2.56 mm². At a scan rate of 500.0 mV/s the peak current was 5.61 µA. Determine the diffusion coefficient, D, for o-DIA. D = cm2/s Determine the peak current if the scan rate is reduced to 350.0 mV/s. Ipe = HA %3D

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What would the potential of a standard hydrogen electrode (S.H.E.) be under the following conditions? [H*] = 0.12 M Pa, = 2.2 atm T = 298 K %3D E =
What volume of 1.00 M NaOH is required to neutralize 35.0 mL of 0.220 M H2SO4?
Calculate the dielectric constant of the medium for the zone between a metal and the OHP layer from the Helmholtz model, when the differential capacitance of the electrode is 1.4 mF cm-2. Indicate, according to this model, what this differential capacity will be like when the potential is reduced by half. Data: distance between metal and OHP layer 4 A, vacuum dielectric constant epsilon0 = 8.85·10-12 F m-1
Explain what are membrane selective electrode also explain their application and their types?
The limiting current was observed to be 60.3 μA in the voltammogram for a 40.0 ml solution of 0.00400 M Cu²+. The current in the limiting-current region was continued for 50.2 min. Calculate the percentage decrease in the concentration of the solution. 4,032 percentage decrease: Incorrect
5 wered out of question Cyclic voltammetry is a very powerful technique to obtain the information about kinetics, thermodynamics and mass transport for an electrode reaction. Diffusion coefficient is an important mass transport related parameter governing an electrode reaction. It may be determined using transient voltammetry. A species Red undergoes a reversible one-electron transfer reaction to form Ox, Red Ox+e An oxidation peak current of 2.08 x 105 A was obtained from a voltammetric experiment undertaken at 25 °C in an aqueous electrolyte medium containing 1.0 mM Red and 0.1 M KCl using a 3.0 mm diameter electrode at a scan rate of 100 mV s¹. Calculate the diffusion coefficient in the unit of cm² s¹ for Red using the Randles-Sevčik equation and choose the correct answer from the following list: Select one: O a. 1.2 x 10-6 Ob. 2.4 x 106 O c. 2.4 x 10-5 O d. 1.2 x 10-5 Your answer is incorrect.
Two Copper strips were used to determine the effect of supporting electrolyte used on the change in mass. Three different experiments were conducted for 5mins where 0.5A current is applied throughout the experiment. In the first experiment two copper strips were immersed in 3.080g of Cu (NO3)2 dissolved in 25mL of DI water and tested for 5mins while applying current 0.5A. The weight of one copper strip act as an anode is taken before the reaction and after the reaction to calculate the change in mass due to different applied current. Same process is repeated with 25ml 0.5 M CuSO4 and25ml 0.5 M CuCl2 for 5 mins Using Faraday’s equation (Eq 1), calculate the theoretical mass and Compares the theoretical mass (mg) of copper and the actual mass deposited (obtained from the electrolysis, ∆m) by calculating the %error at different times. Discuss the observed results. Q = I x t = nFN Electrolyte Initial mass of anode (mg) Final mass of anode (mg) Cu (NO3)2 2941 2893…
please answer fast
3.8 Km/s to m/year 25m/s to miles/hr 8.24 g/cm^2 to mg/mm^2
A corrosion cell is made of Zn anode electrode (EO-0.762 V, p-0.1 V and ig-10 mA/cm) and a hydrogen electrode on metal M surface (M-NI, Eo-0V and p-01 V). Determine the corrosioe rate of Zn electrode in mA/em [enter only the value without the unit in decimal format, eg 3.405, 0.123,0.00012 etc] Metal M Zn Zn2+ H* Anode Zn Electrode Hydrogen Cathode Electrode 12
A Zn wire and Ag/AgCl reference electrode (E° = 0.197 V) are placed into a solution of ZnSO4. The Zn wire is attached to the positive terminal and the Ag/AgCl electrode is attached to the negative terminal of the potentiometer. Calculate the [Zn2+ ] in the solution if the cell potential, Ecell, is -1.091 V. The standard reduction potential of the Zn2 +/Zn half-reaction is –0.762 V.
why the reference electrode can serve as a probe to measure relativereduction potentials or even detect a change in pH of solution