The "over-the-air" television channel 10 operates between frequencies 192 MHz and 198 MHz, with the video and audio using different parts of this frequency range. To watch (and listen) to the channel properly, the tuner circuit in a television must resonate in the middle of this range (195 MHz) and produce a current over the whole range of at least 50% of the peak current at resonant frequency. A particular television tuning circuit is built with a 16.8 pF capacitor, a variable inductor, and a variable resistor. What value should the resistor be in order for the current at both 192 MHz and 198 MHz to be at least 50% of the current at the resonant frequency? Hint:You'll have to first calculate the value of the inductor so that the television tunes to channel 10.

The "over-the-air" television channel 10 operates between frequencies 192 MHz and 198 MHz, with the video and audio using different parts of this frequency range. To watch (and listen) to the channel properly, the tuner circuit in a television must resonate in the middle of this range (195 MHz) and produce a current over the whole range of at least 50% of the peak current at resonant frequency. A particular television tuning circuit is built with a 16.8 pF capacitor, a variable inductor, and a variable resistor. What value should the resistor be in order for the current at both 192 MHz and 198 MHz to be at least 50% of the current at the resonant frequency? Hint:You'll have to first calculate the value of the inductor so that the television tunes to channel 10.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the voltage ratio that corresponds to 88.57 dB? a) 2404 O b) 26,833 O c) 4/(5 × 105) O d) 24(3 x 107)
i need the answer quickly
Please solve colpitts oscillator why does the output change when the inductor value is changed.
Skin effect becomes less effective in Lower frequency Higher frequency Both higher and lower frequencies none of the choices
Comment on the frequency components of the output from the modulator
The below 4 figures are the angle of the transfer function of passive filters. Phase (deg) -45- Phase (deg) (Cep) sid 45 10 10 Frequency (radisec) 10² Frequency (rad/sec) Figure-1 shows the frequency response of Figure-2 shows the frequency response of Figure-3 shows the frequency response of Figure-4 shows the frequency response of 4) ( + 4 10 10" 10
For the given circuit in figure 6, determine the upper and lowerfrequencies of oscillation and also the Hartley oscillators bandwidth.
Determine Vo if an signal of 2mV is applied at the input: Vec =16V 39 k0 39 k2 B=100 4.7 k2 12 k2 10 uF
In the figure below, the alternating current bridge is in equilibrium with the following constants: Arm AB, R = 350 Q; arm BC, R = 200 Q, series with C = 0.265 µF; CD arm unknown; arm DA, R = 100 Q in series with L = 15.9 mH, if the oscillator frequency is 1 %3D KHz, determine the value of the arm constants CD. Zz D
Build, and test the oscillator: 1. Use R = 7.2 KQ, C = 1.0 nF, and C2 = 0.1 μF. 2. Calculate the frequency of the oscillator using Eqs. T = tc + td.and tc = td = 0.693 RC 3. Measure the frequency and duty cycle of the output waveform. Vcc charge R w U Reset 4 Discharge 7 Threshold 6 Trigger C₂ 2 Control 8 Voc Open RST' R a 10 3 Q' 1 Ground Out Figure 3: A square wave generator based on 555-timer.
What is the voltage ratio that corresponds to 88.57 dB? O a) 2404 O b) 26,833 Oc) 4/(5 × 105) O d) 24(3 x 107)