The nozzle which furnished the water to a certain hydraulic turbine 280 mm in diameter and has a coefficient of velocity and discharge of 0.98 and 0.95 respectively. The nozzle supplied from 60 cm in diameter pipe in which water approached the nozzle with a total head of 335 m. Compute for the power in kN/s delivered by the jet to the turbine

The nozzle which furnished the water to a certain hydraulic turbine 280 mm in diameter and has a coefficient of velocity and discharge of 0.98 and 0.95 respectively. The nozzle supplied from 60 cm in diameter pipe in which water approached the nozzle with a total head of 335 m. Compute for the power in kN/s delivered by the jet to the turbine

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Francis turbine has an inlet diameter of 2 m and an outlet diameter of 1 m. The breadth of the blades is constant as 0.2 m. The peripheral velocity at inlet is given as 25 m/s. The vanes are radial at the inlet and the discharge is radially outwards at the outlet. The peripheral velocity of the blade at outlet will be (a) 15 m/s (c) 20 m/s (b) 25 m/s (d) 12.5 m/s
Water at 20°C is being pumped from tank 1 to tank 2 with given conditions. Calculate the power of pump used in the system. (Both tanks are open to atmosphere).
Water flows through a pipe at 150 L/s changes gradually in diameter from 165 mm at point M to 473 mm The and that м is respective pressures point m higher point at N. 4.3 than N. at point M and N are 72 kPa 49.8 kPa. a. Determine the head lost of the pipe. b. Determine the total energy at point N with datum at point M. c. Determine the total energy at point M with datum at point M.
A well-insulated turbine operating at steady state is shown on the right. Steam enters at 3 MPa, 400°C, with a volumetric flow rate of 85 m³/min. Some steam is extracted from the turbine at a pressure of 0.5 MPa and a temperature of 180°C. The rest expands to a pressure of 6 kPa and a quality of 90%. The total power developed by the turbine is 11,400 kW. Kinetic and potential energy effects can be neglected. Determine (a) the mass flow rate (in kg/s) at each exit, and (b) the diameter of the duct, d₂ (in cm) where steam is extracted P₁ = 3MPa T₁=400°C (AV)₁ = 85 m³/min Turbine P2 = 0.5 MPa T₂ = 180°C V₂= 20 m/s Power out ¹3 P3= 6 kPa x3 = 90%
A pump draws water from a large open sump through a short length of the suction pipe. The water is delivered through a 21.1 m length of 9 cm diameter pipe and via a submerged exit into an open tank. A control valve is installed in the delivery pipe, for which f = 0.0085. Dissipation other than friction and the loss at the valve may be ignored. The bottom of the tank is 10 m above the free surface of the water in the sump. What power will be required in kW if the water will be delivered to 1.5m above the pump?
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure . The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. 1. Compute the Power delivered by the pump in kw ( A. 79.07 , B. 48.10 C. 13.08 , D. 57.23) 2. Compute the Pressure head at point 1 in m. ( A. 85.96 , B. 19.74 C. 245.09 , D. 45.90) 3. Pressure head at point 2 in m. ( A. 104.51 , B. 246.67 C. 57.84 , D. 12.69)
6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and has coefficients of velocity and discharge of 0.98 and 0.96, respectively. The nozzle is supplied from a 60cm pipe in which the water approached the nozzle with a total head of 330m. Compute the following: a. Energy per second delivered by the jet to the turbine. b. Energy measured in hp lost in passing through the nozzle.
A nozzle is fitted at the end of a pipe of length 100 m and of diameter 150 mm. For the maximum transmission of power through the nozzle, determine the diameter of nozzle. Take f = .009.
A four-stage (parallel) pump delivers 15 m3 1950 rpm. It is desired to construct a pump at a certain number of stages in series that should run at 1450 rpm delivering 18m/min with 280m of head in total. What should be the new diameter of the impeller and number of stages? per minute of liquid. The total head obtained is 27m. Initially, the impeller measures 24cm in diameter running at
The 600 mm pipe shown conducts water from reservoir A to a pressure turbine, which discharges through another 600 mm o pipe into tail race B. The head lost from A to 1 is 5 times the velocity head in the pipe and the head lost from 2 to B is 0.2 times the velocity head in in the pipe. If the discharge is 700 L/s A) Compute for the total head lost 1. 05: Compute for the extracted energy cause by the turbine Compute for the hp given up by the turbine. V Answer A) EL 60m 600 mm 1.63 m 58.37 m 537.3 hp 600 mm o B ▷ EL 0 m
the water exits the 400-mm-diameter pipe at 8 m/s. Neglect all losses. 2. Determine the power delivered to the turbine if 20 m (P= 243.969 kW) 8 m EDIFIC 1911