The normal and shear stresses in a bar must be limited to σmax and τmax. Each limit is used to calculate a required cross-sectional area for the bar. Which of the two cross-sectional areas should the designer use? The normal and shear stresses in a bar must be limited to amax and tmax. Each limit is used to calculate a required cross-sectionalarea for the bar. Which of the two cross-sectional areas should the designer use?A the larger area(B the smaller areathe area associated with omaxthe area associated with tmax

Answer:- A Option A " the larger area " is the correct answer. Explanation:- A designer must…

The normal and shear stresses in a bar must be limited to omax and tmax. Each limit is used to calculate a required cross-sectional area for the bar. Which of the two cross-sectional areas should the designer use? the larger area B the smaller area the area associated with omax the area associated with tmax

The normal and shear stresses in a bar must be limited to omax and tmax. Each limit is used to calculate a required cross-sectional area for the bar. Which of the two cross-sectional areas should the designer use? the larger area B the smaller area the area associated with omax the area associated with tmax

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given: E= 29x10^6 psi A= 2in^2 Determine the deformations members AB, BC, BE, DE and DF. Please show your complete handwritten solution.
The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment My = 55 Nm. (Hint: use Page 7-9 in your notes) Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
Describe the Plane Strain and Axisymmetrical Strain.
Shea Where G is the shear modulus and can be writte ratio that is: 9 = Elateral %3D - Eaxlal
Explain with a sketch the method which is used to compute the stress ratio.
Assignment Problem 10.1. A steel bar of diameter d = 52 mm is twisted by torques at the ends. The allowable shear stress is 65 MPa. What is the maximum torque that can be applied?
20. A steel section is subjected to a combination of shear and bending actions. The applied shear force is V and the shear capacity of the section is Vs. For such a section, high shear force (as per IS: 800-2007) is defined as A. V> 0.6 Vs B. V> 0.7 Vs C. V> 0.8 Vs D. V> 0.9 Vs
Please explain with all detail steps
I need the answer as soon as possible
20. A steel section is subjected to a combination of shear and bending actions. The applied shear force is V and the shear capacity of the section is Vs. For such a section, high shear force (as per IS: 800-2007) is defined as A. V> 0.6 Vs B. V> 0.7 Vs C. V> 0.8 Vs D. V> 0.9 Vs