The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation of the shafts. Assume Ng=44 teeth and Nc=28 teeth. a) Shaft (2) is a solid 36-mm-diameter steel shaft. Determine the maximum shear stress T2 produced in shaft (2). b) If the shear stress in shaft (1) must be limited to 43 MPa, determine the minimum acceptable diameter d, for shaft (1) if a solid shaft is used.

The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation of the shafts. Assume Ng=44 teeth and Nc=28 teeth. a) Shaft (2) is a solid 36-mm-diameter steel shaft. Determine the maximum shear stress T2 produced in shaft (2). b) If the shear stress in shaft (1) must be limited to 43 MPa, determine the minimum acceptable diameter d, for shaft (1) if a solid shaft is used.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The solid shaft is fixed at A and free at D. It is subjected to three concentrated torques at B, C…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: A shaft is fixed at support C and has a torque of 75lb.ft with respect to free end at a distance of…

A: givenM1=75lbft at 0.75ft from fixed end CW2=1200lb/ft M2=600lbft at free end

Q: Problem 5-57: The turbine develops 150 kW of power, which is transmitted to the gears such that C…

A: Given data as per the questionpower developed =150 kwdiameter of shaft =100 mm =0.1 mRotational…

Q: Consider a solid circular shaft A-D with varied diameter (dAB=0.6 in, d³c-0.75 in, and dcp=0.9 in).…

A: In conclusionFinding the exact location of maximum shear stress and plotting the shear stress…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

Q: For the gear system shown in the figure, the diameter of shaft AB=12 mm. Determine the diameter of…

Q: The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a…

A: A Determine the force on gear D due to the torque acting at end A.Here, TA is the applied torque at…

Q: 3. A steel shaft 60 in. long has applied to it a 10,000 in-lb torque by a pulley located at the…

Q: A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: 2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Mşi, d=1.0" (inch),…

A: Assume the shaft is static initially and evaluate the reaction forces at bearing supports.Consider…

Q: Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an…

A: Given data, Power=150hp speed=250 rpm shear stress=4.7ksi angle of twist =0.35°…

Q: The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a…

Q: Problem 2: A steel tube having an outer diameter of 2.5 in. is used to transmit 10 hp when turning…

A: Given:D=2.5 inP=10 hpN=30 rpmζallow=12 ksi

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

The motor supplies 11.1 kW at 19.9 Hz at A. The bearings shown permit free rotation of the shafts. Assume Ng=44 teeth and Ne=28 teeth.
(a) Shaft (2) is a solid 36-mm-diameter steel shaft. Determine the maximum shear stress T2 produced in shaft (2).
(b) If the shear stress in shaft (1) must be limited to 43 MPa, determine the minimum acceptable diameter d, for shaft (1) if a solid shaft is used.
NB
В
(1)
Nc
Tp
(2)
Answers:
MPa.
(a) T2 =
mm.
(b) di =

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in diameter, at a speed of 300 rpm. Power is drawn from the shaft using belts attached to pulleys A and C. (Use the table if necessary) (a) Draw the torque diagram of the driven shaft. (b) What is the safety factor of the driven shaft? Answer: 5.22 (c) Determine the angle of torsion of pulley C with respect to pulley A. Answer: -1.88°
The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a coupling with eight bolts. The bolt circle diameters are 5 and 10 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. O 0 600 rev/min Determine the minimum nominal shoulder diameter of a bolt if all bolts are to have the same diameter and not exceed a shear stress of 20 kpsi Select a preferred fraction size. The minimum nominal shoulder diameter of a bolt is, in.
I really need help with this! Please answer it using the Maximum shear stress theory, and also be very clear with your explanation. Thank you!
please help solve
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
Please I want answer of that question from these choices
A static shaft is subjected to torques at A, B, and C. It has a diameter of 58 mm and is made from 2014-T6 aluminum. If the maximum allowable magnitude of the angle of twist of C relative to A is 0.04 rad, what is the maximum value for the torque T? A aT T cc i❀O 2021 Cathy Zupke parameter value 1.4 1.6 0.6 L₁ L2 α B units m m [-] (1-a )T The maximum value for T is 1.56 X kN.m.
Only HAndwritten answer please
Determine the minimum required diameter of the shaft CD.
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(t) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rads. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as c, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). O(1) ke M(1) = M, cos ot Turbine rotor, Jo
A compound shaft drives several pulleys, as shown. Segments (1) and (2) of the compound shaft are hollow aluminum (G = 4000 ksi) shafts that have a polar moment of inertia of J = 2.835 in4. Segments (3) and (4) are solid steel (G = 12000 ksi) shafts that have polar moment inertia of J = 1.024 in4. The bearings shown allow the shaft to turn freely. Assume TB = 980 lb.ft TD= 525 lb.ft TE = 130lb.ft L1 =74in L2 =29in L3 =34in L4 =35in. Calculate the rotation angle (including the correct sign) of pulley E with respect to point A.
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm