Answered: the modulus of the pressure force on…

Engineering

Civil Engineering

the modulus of the pressure force on the 3-m wide gate AB and center of pressures.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H =2m Seawater y = 0.2x2 y 25 m The concrete seawall given in Figure 4 has a curved surface and restrains seawater at a depth of 2 m. The trace of the surface is a parabola as illustrated. Determine the force of the fluid force (per unit length) with respect to an axis through the toe (point A). 1024kg/m³) (Y seawater = -X
As shown in the figure compute the amount and location of the vertical and horizontal components of the hydrostatic pressure on XY 1. Rectangular 5ft wide 7 W.S X * a= 6ft b= 8ft c= 4ft
In the figure below, determine the force F (newton) to balance the weight of the cylinder. |ylinder W 44 kN A = 0.323 m? F = ? Plunger, a = 0.00323 m? 4.6 m YOil, s = 0.78 YOil, s = 0.78 Assume that the weight
2. In figure below fluid 1 is oil (SG=0.87) and fluid 2 is glycerin (SG=1.26) at 20°C. If P₁ = 98kPa, determine the absolute pressure at point A. Gu 10 cm P₂ Pa 32 cm Figure 2. Schematic for problem 2
Water is flowing with flow rate 5 liter/s in a straight 50 mm diameter galvanized iron pipe as shown in the figure. Determine the pressure difference between point A and B by using Darcy-Weisbach formula, and Hazen-William's formula
Note:hand written solution should be avoided.
show full solution, 2 decimal places for final answer.
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z=20ft. a. The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c. The hydrostatic force due to water. d. The net hydrostatic force acting on the gate Fnet
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 426 mm2 . Determine the average axial stress in each bar.
Please answer in two decimal places po
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3
I need the answer to the question in fluid mechanics