-The modulating signal into an FM modulator is m(t) = 2 cos(16nt) and the carrier is c(t) = 12 cos(5000 rt), k p= 4. If the output of the FM modulator is passed through an ideal BPF centered at f. =2500 with a bandwidth of 32 Hz, a. Determine the power of the frequency components at the output of the filter b. What percentage of the transmitter power appears at the output of the BPF?

-The modulating signal into an FM modulator is m(t) = 2 cos(16nt) and the carrier is c(t) = 12 cos(5000 rt), k p= 4. If the output of the FM modulator is passed through an ideal BPF centered at f. =2500 with a bandwidth of 32 Hz, a. Determine the power of the frequency components at the output of the filter b. What percentage of the transmitter power appears at the output of the BPF?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

. Determine the frequency of the modulating signal which is producing an FM signalhaving a bandwidth of 50 kHz when the frequency deviation of the FM signal is 10 kHz.
For a square modulating signal with value 0 and 3 V entering an FM modulator with drift sensitivity of 0.1KHz / V and a carrier frequency of 100KHz with Vc = 5V, draw the waveform of the resulting modulated signal indicating the frequency and amplitude values of the wave.
An FM signal has a maximum frequency deviation of 1500h and a modulating frequency of 500h, its total power is 6500w, applied to a resistive load of 1ohm, the carrier frequency is 400Mhz. Determine the sensitivity of the modulator, and the magnitude spectrum
i need the answer quickly
D E F
For single-sideband production in AM SSBSC, three transmitter configurations are typically used: the filter approach, the phase-shift method, and the so-called third method. A bandpass filter circuit is used in the filter method to reject one sideband and transmit the remaining sideband. The modulating signal and carrier are applied directly to one of the modulators in the phase-shift method, then both are moved 90 degrees and applied to the second modulator. The outputs of the two balanced modulators are double-sideband suppressed-carrier signals with the proper phase, so that one of the sidebands is canceled when they are combined in a linear summer. The disadvantage of single-sideband transmission is which of the following statements? Select your answer. Tuning single-sideband receivers is more difficult and precise than tuning DSBSC AM receivers. Because most single-sideband transmissions involve a suppressed carrier, envelope detection cannot be employed unless the carrier is…
Given that the maximum and minimum values of the envelope of an AM modulated sinusoidal signal are 3.5 V and 0.9 V, respectively, what would be the modulation index? Note that there is no over-modulation in this case.
all 4
A plot of the exponential spectrum of the signal x(t) = 4 sin(200πt) +12 sin(1000 πt) will have a peak amplitude of _______ at -500Hz as well as a bandwidth of ______Hz.. Single choice.
For an FM modulator with 48 kHz of frequency deviation. and a modulation signal frequency fm= 8kHz, determine the bandwidth using both the Bessel table and Carson's rule.
Q1): Use the PCM method to convert the signal below into a digital signal by assuming fm = 1000 Hz and n- 3. 4 -5 0.5 1 1.5 2.5 3 3.5 4 4.5 5 Time(ms) Q2): Use the DPCM method to: 1. convert the signal below into a digital signal by assuming fm = 500 Hz and n = 3. 2. reconstruct discrete signal at the receiver end. 3. calculate the error between the sampled discrete signal at transmitter end and the reconstructed discrete signal at the receiver end. 3 2 -2 3 2 3 4 5 10 1, (HOA) apnadury Amplitude (volt)
An FM radio broadcast used a modulator with a frequency deviation sensitivity of 5KHz/V, a 2Vp – 10 kHz modulating signal, and a 10Vp – 88MHz carrier Signal , determine. Use this Bessel table below to solve this problem. (a) Actual minimum bandwidth from the Bessel function table in kHz