the mobile crane (weight =48 kN) moves across the brige of length, l =14m. the front wheels of the mobile carry the three-quarter of its weight while the rear wheels carry a quarter of its weight. iif the distance between front and rear wheel is b = 0.7m. Determine themaximum value of bending moment as it moves across

Q: Ql. EI 2EI a A M.

A: Detailed solution below. Hope it will help you. Good Luck.

Q: Compute the value of EIy at 2.5 m from the left support.

A:

Q: Calculate the member forces of the loaded structure. y 60 kN D 40 kN 7 m C, 3 m Ax Ay -4 m-

A:

Q: etermine the moment at support A of the compound beam. Assume A is fixed a pin, and C is a roller. A…

A: To find moment at point A

Q: If the distance between E and Bis h= 0.3 m, calculate the maximum absolute values of the shear and…

A: Given Data  Find maximum absolute shear force and bending moment.

Q: Problem 3: For the beam shown in Figure 3. A. Find the reaction support B (R) B. Find the reaction…

A: To find support reaction at point B and D

Q: Determine the support reactions of the following structure using force method. Only consider the…

A:

Q: MOVING LOADS: SITUATION: A simple beam AB supports two connected wheel loads P and 2P that are…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

A:

Q: Solve the angle of twist on a solid shaft, 2in in diameter and 1ft in length, if the torque applied…

A:

Q: A beam is loaded and supported as shown in the figure bellow, determine the magnitude of the maximum…

A: in given question  V1+V2=55×6+110V1+V2=440 taking moment at B V1×10-220-55×6×9-110×4=0V1=363KN and…

Q: Use E= 200 GPa, I = 800 x 106 mm² when necessary. P = 229kN For the beam loaded as shown, determine…

A: Data given Find: Reaction components

Q: For the loaded structure below, replace the force system with a single resultant force. Determine…

A: The  conversion of UDL into point load; P=(1/2)*3*42 P=6 KN from A at (2/3)*3=2 m

Q: Determine the value of bending moment in column 3 (in kip-ft, absolute value) if the bay width is 20…

A:

Q: Determine the value of bending moment in column 1 (in kip-ft, absolute value) if the bay width is 29…

A:

Q: What is the Maximum moment in kN-m. Given: w =48, a = 4, b = 4, and c = 2.

A:

Q: Three wheel load rolls as a unit across a 12 span. The loads are A=15kn B=25kn, 2m to the right of…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A 15 kN; B = 25 kN, 2 m to the…

A:

Q: Determine the moment at B in kN-m.

A:

Q: or the frame shown, the Moment Distribut )to draw the shear and bending moment ettlement of 0.25…

A: In the above question, a frame is given with all information we need to determine the following…

Q: F₁ O 260 kN (C) O 170 KN (C) 180KNC) F₂ F₂ 'В d₂ (2) C

A:

Q: 3) A truck and trailer combination having the axle loads as shown in the figure rolls across the…

A:

Q: A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load…

A:

Q: Q4. The T-beam is supported by a pin support at point A and a roller support at point B, and the…

A:

Q: Determine the following: a. Maximum negative shear at B b. Maximum positive shear at B c. Maximum…

A:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.