The member shown in Fig. 5-14a is pin-connected at A and rests against a smooth support at B. Determine the horizontal and vertical components of reaction at the pin A. B 30 0.75 m 90 N m 1 m 0.5 m 60 N (a) 30 30 A, 0.75 m 90 N m Im 60 N (b)

Q: The bend rod is supported at A, B, and C by smooth journal bearings. Determine the components of…

A:

Q: Q/ In the shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200…

A: Givenm=50kgM=200kg

Q: For the beam AB shown in the image below, select the correct FBD in order to determine the support…

A:

Q: The ABC lever is supported at point A and connected to a short connection BD as shown in Fig.5-22a.…

A: Draw the free-body diagram of the lever ABC :

Q: Problem 1 Determine the reaction at A and C. Support at A is fixed, C is roller support, and B is…

A:

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A:

Q: The system in the figure is in equilibrium. A concrete block of mass 243 kg hangs from the end of…

A: (a) Tension in wire, T = 1686.73 N. (b) Horizontal reaction at hinge, Rx = 1466.6 N→. (c) Vertical…

Q: Problem Statement Based on Problem 5-47 from the textbook. Determine the reactions at the pin A and…

A:

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A: Answer: ◆ T = 7646 N , FBx = 3823 N , FBy = 4169 N. ◆ Option (C) is correct.

Q: The composite beam shown in the figure is connected by a pin. in b. Determine the moments at A, B,…

A:

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A: find the tension in the cable and reaction at support B.

Q: The light bom Wall by a bal AB IS attached to9 vertical at A and Suppore and socket point by two…

A:

Q: Q/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg) and…

A:

Q: Given the assembly in equilibrium as shown in the figure, determine the following: 1. Tension in…

A:

Q: The smooth uniform rod AB is supported by a ball-and-socket joint at A, the wall at B, and cable BC.…

A: Given:The mass of the uniform rod is, .The acceleration due to gravity is, .Tension in cable BC is,…

Q: The system in the figure is in equilibrium. A concrete block of mass 265 kg hangs from the end of…

A: Given-To Find-(i) Tension  in the cable(ii) horizontal component of Force on strut from hing(Iii)…

Q: Exercise 5.7: The member shown in fig 5-9 is a smooth support at B. Determine the horizontal and…

A:

Q: 5-77. The member is supported by a square rod which fits loosely through the smooth square hole of…

A:

Q: The uniform bar AB shown in Fig. weighs 100 Ib. If the spring has an unstretched length of 5 ft, de-…

A: Given data : Let x = 6 ft                     Let y= 8 ft                     Then AB = 10 ft ( from…

Q: A body of weight N is lying on not a smooth plane inclined at an angle of 31° with the parallel. It…

A:

Q: A member (AC) is supported by a pin at A and a roller at B. The horizontal component of reaction at…

A: Let us draw the reaction supports

Q: Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum.

A:

Q: A member (AC) is supported by a pin at A and a roller at B. The horizontal component of reaction at…

A: The horizontal component of the reaction at pin A: Option (b) : Ax = 4 kN

Q: (NOS. 4-7) PROBLEM 2. Two rollers of the same diameter shown are supported by an inclined plane and…

A:

Q: 5. The bent rod of negligible weight is supported by a ball-and-socket joint at A and a single…

A:

Q: For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A…

A: According to the given data Case-1 M is clockwise and Ax=0 Case-2 M is anti-clockwise Ax≠0  We need…

Q: Homework: The pin-connected structure of Figure below has the 2400 N.mm moment applied to member…

A:

Q: 5-31. The mass of 700 kg is suspended from a trolley which moves along the crane rail from d=1.7 m…

A: To determine:The force along the pin connected knee struct BCThe magnitude of force at pin A=

Q: 4. Determine the forces P, F, and T required to keep the triangular frame shown in the figure in…

A:

Q: Make the free body diagram and calculate the reaction efforts at the points with movement…

A: Length, L1=1.9 m Length, L2=3.3 m Length, L3=3.5 m Load, P1=75 kN Load, P2=140 kN

Q: A member (AC) is supported by a pin at A and a roller at B. The horizontal component of reaction at…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: Determine the magnitude of each of the reactions at the supports; roller at A and pin at B. 0 = 30…

A:

Q: D 50 kN 25 kN

A: This is a simple truss problem. In this question we calculate the reactions at the supports by…

Q: W B A Y Fj FM

A:

Q: 4-60. Determine the magnitude of the moment produced by the force of F 200 N about the hinged axis…

A:

Q: rmine the force in membe for the truss loaded and supported a shown in figure (3). Does the…

A:

Q: Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C…

A:

Q: The following figure shows a hollow piston of weight W-50 N and diameter D=3d occupies the position…

A: Given: The piston weight, W = 50 N The diameter of piston, D = 3d The diameter of lateral tube, d1 =…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.